Welded aluminium alloy bicycle frame, made in the 1990s
An aluminium alloy (UK/IUPAC) or aluminum alloy (NA; see spelling differences) is an alloy in which aluminium (Al) is the predominant metal. The typical alloying elements are copper, magnesium, manganese, silicon, tin, nickel and zinc. There are two principal classifications, namely casting alloys and wrought alloys, both of which are further subdivided into the categories heat-treatable and non-heat-treatable. About 85% of aluminium is used for wrought products, for example rolled plate, foils and extrusions. Cast aluminium alloys yield cost-effective products due to the low melting point, although they generally have lower tensile strengths than wrought alloys. The most important cast aluminium alloy system is Al–Si, where the high levels of silicon (4–13%) contribute to give good casting characteristics. Aluminium alloys are widely used in engineering structures and components where light weight or corrosion resistance is required.[1]
Alloys composed mostly of aluminium have been very important in aerospace manufacturing since the introduction of metal-skinned aircraft. Aluminium–magnesium alloys are both lighter than other aluminium alloys and much less flammable than other alloys that contain a very high percentage of magnesium.[2]
Aluminium alloy surfaces will develop a white, protective layer of aluminium oxide if left unprotected by anodizing and/or correct painting procedures. In a wet environment, galvanic corrosion can occur when an aluminium alloy is placed in electrical contact with other metals with more positive corrosion potentials than aluminium, and an electrolyte is present that allows ion exchange. Also referred to as dissimilar-metal corrosion, this process can occur as exfoliation or as intergranular corrosion. Aluminium alloys can be improperly heat treated, causing internal element separation which corrodes the metal from the inside out.[citation needed]
Aluminium alloy compositions are registered with The Aluminum Association. Many organizations publish more specific standards for the manufacture of aluminium alloy, including the SAE International standards organization, specifically its aerospace standards subgroups,[3] and ASTM International.
Engineering use & properties
[
edit
]
Aluminium alloy bicycle wheel. 1960s Bootie Folding CycleAluminium alloys with a wide range of properties are used in engineering structures. Alloy systems are classified by a number system (ANSI) or by names indicating their main alloying constituents (DIN and ISO). Selecting the right alloy for a given application entails considerations of its tensile strength, density, ductility, formability, workability, weldability, and corrosion resistance, to name a few. A brief historical overview of alloys and manufacturing technologies is given in Ref.[4] Aluminium alloys are used extensively in aircraft due to their high strength-to-weight ratio. Pure aluminium metal is much too soft for such uses, and it does not have the high tensile strength that is needed for building airplanes and helicopters.
Aluminium alloys versus types of steel
[
edit
]
Aluminium alloys typically have an elastic modulus of about 70 GPa, which is about one-third of the elastic modulus of steel alloys. Therefore, for a given load, a component or unit made of an aluminium alloy will experience a greater deformation in the elastic regime than a steel part of identical size and shape. With completely new metal products, the design choices are often governed by the choice of manufacturing technology. Extrusions are particularly important in this regard, owing to the ease with which aluminium alloys, particularly the Al-Mg-Si series, can be extruded to form complex profiles.
In general, stiffer and lighter designs can be achieved with aluminium alloy than is feasible with steels. For instance, consider the bending of a thin-walled tube: the second moment of area is inversely related to the stress in the tube wall, i.e. stresses are lower for larger values. The second moment of area is proportional to the cube of the radius times the wall thickness, thus increasing the radius (and weight) by 26% will lead to a halving of the wall stress. For this reason, bicycle frames made of aluminium alloys make use of larger tube diameters than steel or titanium in order to yield the desired stiffness and strength. In automotive engineering, cars made of aluminium alloys employ space frames made of extruded profiles to ensure rigidity. This represents a radical change from the common approach for current steel car design, which depend on the body shells for stiffness, known as unibody design.
Aluminium alloys are widely used in automotive engines, particularly in engine blocks and crankcases due to the weight savings that are possible. Since aluminium alloys are susceptible to warping at elevated temperatures, the cooling system of such engines is critical. Manufacturing techniques and metallurgical advancements have also been instrumental for the successful application in automotive engines. In the 1960s, the aluminium cylinder heads of the Chevrolet Corvair earned a reputation for failure and stripping of threads, which is not seen in current aluminium cylinder heads.
An important structural limitation of aluminium alloys is their lower fatigue strength compared to steel. In controlled laboratory conditions, steels display a fatigue limit, which is the stress amplitude below which no failures occur – the metal does not continue to weaken with extended stress cycles. Aluminium alloys do not have this lower fatigue limit and will continue to weaken with continued stress cycles. Aluminium alloys are therefore sparsely used in parts that require high fatigue strength in the high cycle regime (more than 107 stress cycles).
Heat sensitivity considerations
[
edit
]
Often, the metal's sensitivity to heat must also be considered. Even a relatively routine workshop procedure involving heating is complicated by the fact that aluminium, unlike steel, will melt without first glowing red. Forming operations where a blow torch is used can reverse or remove the effects of heat treatment. No visual signs reveal how the material is internally damaged. Much like welding heat treated, high strength link chain, all strength is now lost by heat of the torch. The chain is dangerous and must be discarded.[citation needed]
Aluminium is subject to internal stresses and strains. Sometimes years later, improperly welded aluminium bicycle frames may gradually twist out of alignment from the stresses of the welding process. Thus, the aerospace industry avoids heat altogether by joining parts with rivets of like metal composition, other fasteners, or adhesives.
Stresses in overheated aluminium can be relieved by heat-treating the parts in an oven and gradually cooling it—in effect annealing the stresses. Yet these parts may still become distorted, so that heat-treating of welded bicycle frames, for instance, can result in a significant fraction becoming misaligned. If the misalignment is not too severe, the cooled parts may be bent into alignment. If the frame is properly designed for rigidity (see above), that bending will require enormous force.[citation needed]
Aluminium's intolerance to high temperatures has not precluded its use in rocketry; even for use in constructing combustion chambers where gases can reach 3500 K. The RM-81 Agena upper stage engine used a regeneratively cooled aluminium design for some parts of the nozzle, including the thermally critical throat region; in fact the extremely high thermal conductivity of aluminium prevented the throat from reaching the melting point even under massive heat flux, resulting in a reliable, lightweight component.
Household wiring
[
edit
]
Because of its high conductivity and relatively low price compared with copper in the 1960s, aluminium was introduced at that time for household electrical wiring in North America, even though many fixtures had not been designed to accept aluminium wire. But the new use brought some problems:
All of this resulted in overheated and loose connections, and this in turn resulted in some fires. Builders then became wary of using the wire, and many jurisdictions outlawed its use in very small sizes, in new construction. Yet newer fixtures eventually were introduced with connections designed to avoid loosening and overheating. At first they were marked "Al/Cu", but they now bear a "CO/ALR" coding.
Another way to forestall the heating problem is to crimp the short "pigtail" of copper wire. A properly done high-pressure crimp by the proper tool is tight enough to reduce any thermal expansion of the aluminium. Today, new alloys, designs, and methods are used for aluminium wiring in combination with aluminium terminations.
Alloy designations
[
edit
]
Wrought and cast aluminium alloys use different identification systems. Wrought aluminium is identified with a four digit number which identifies the alloying elements.
Cast aluminium alloys use a four to five digit number with a decimal point. The digit in the hundreds place indicates the alloying elements, while the digit after the decimal point indicates the form (cast shape or ingot).
Temper designation
[
edit
]
The temper designation follows the cast or wrought designation number with a dash, a letter, and potentially a one to three digit number, e.g. 6061-T6. The definitions for the tempers are:[5][6]
-F : As fabricated
-H : Strain hardened (cold worked) with or without thermal treatment
-O : Full soft (annealed)
-T : Heat treated to produce stable tempers
-W : Solution heat treated only
Note: -W is a relatively soft intermediary designation that applies after heat treat and before aging is completed. The -W condition can be extended at extremely low temperatures but not indefinitely and depending on the material will typically last no longer than 15 minutes at ambient temperatures.
Wrought alloys
[
edit
]
The International Alloy Designation System is the most widely accepted naming scheme for wrought alloys. Each alloy is given a four-digit number, where the first digit indicates the major alloying elements, the second — if different from 0 — indicates a variation of the alloy, and the third and fourth digits identify the specific alloy in the series. For example, in alloy 3105, the number 3 indicates the alloy is in the manganese series, 1 indicates the first modification of alloy 3005, and finally 05 identifies it in the 3000 series.[7]
1000 series (essentially pure)
[
edit
]
1000 series are essentially pure aluminium with a minimum 99% aluminium content by weight and can be work hardened.
# Not an International Alloy Designation System name
2000 series (copper)
[
edit
]
2000 series are alloyed with copper, can be precipitation hardened to strengths comparable to steel. Formerly referred to as duralumin, they were once the most common aerospace alloys, but were susceptible to stress corrosion cracking and are increasingly replaced by 7000 series in new designs.
3000 series (manganese)
[
edit
]
3000 series are alloyed with manganese, and can be work hardened.
3000 series aluminium alloy nominal composition (% weight) and applications Alloy Al contents Alloying elements Uses and refs 3003 98.6 Mn 1.5; Cu 0.12 Universal, sheet, rigid foil containers, signs, decorative 3004 97.8 Mn 1.2; Mg 1 Universal, beverage cans[24] 3005 98.5 Mn 1.0; Mg 0.5 Work-hardened 3102 99.8 Mn 0.2 Work-hardened[25] 3103&3303 98.8 Mn 1.2 Work-hardened 3105 97.8 Mn 0.55; Mg 0.5 Sheet 3203 98.8 Mn 1.2 Sheet, high strength foil4000 series (silicon)
[
edit
]
4000 series are alloyed with silicon. Variations of aluminium–silicon alloys intended for casting (and therefore not included in 4000 series) are also known as silumin.
4000 series aluminium alloy nominal composition (% weight) and applications Alloy Al contents Alloying elements Uses and refs 4006 98.3 Si 1.0; Fe 0.65 Work-hardened or aged 4007 96.3 Si 1.4; Mn 1.2; Fe 0.7; Ni 0.3; Cr 0.1 Work-hardened 4015 96.8 Si 2.0; Mn 1.0; Mg 0.2 Work-hardened 4032 85 Si 12.2; Cu 0.9; Mg 1; Ni 0.9; Forgings 4043 94.8 Si 5.2 Rod, Welding Filler, Brazing Filler 4047 85.5 Si 12.0; Fe 0.8; Cu 0.3; Zn 0.2; Mn 0.15; Mg 0.1 Sheet, cladding, fillers[26] 4543 93.7 Si 6.0; Mg 0.3 architectural extrusions 4643 93.7 Si 4.1; Fe 0.8; Mg 0.2; Zn 0.1 Welding filler for 6000 series5000 series (magnesium)
[
edit
]
5000 series are alloyed with magnesium, and offer superb corrosion resistance, making them suitable for marine applications. 5083 alloy has the highest strength of non-heat-treated alloys. Most 5000 series alloys include manganese as well.
6000 series (magnesium and silicon)
[
edit
]
6000 series are alloyed with magnesium and silicon. They are easy to machine, are weldable, and can be precipitation hardened, but not to the high strengths that 2000 and 7000 can reach. 6061 alloy is one of the most commonly used general-purpose aluminium alloys.
7000 series (zinc)
[
edit
]
7000 series are alloyed with zinc, and can be precipitation hardened to the highest strengths of any aluminium alloy. Most 7000 series alloys include magnesium and copper as well.
8000 series (other elements)
[
edit
]
8000 series are alloyed with other elements which are not covered by other series. Aluminium–lithium alloys are an example.[45]
8000 series aluminium alloy nominal composition (% weight) and applications Alloy Al content Alloying elements Uses and refs 8006 98.0 Fe 1.5; Mn 0.5; Universal, weldable 8009 88.3 Fe 8.6; Si 1.8; V 1.3 High-temperature aerospace[46] 8011 98.7 Fe 0.7; Si 0.6 Work-hardened 8014 98.2 Fe 1.4; Mn 0.4; universal[47] 8019 87.5 Fe 8.3; Ce 4.0; O 0.2 Aerospace 8025 Si 0.05; Fe 0.06–0.25; Cu 0.20; Mg 0.05; Cr 0.18; Zn 0.50; Ti 0.005–0.02; Li 3.4–4.2; Zr 0.08–0.25 [10] 8030 99.3 Fe 0.5; Cu 0.2 wire[48] 8090 Si 0.20; Fe 0.30; Cu 1.0–1.6; Mn 0.10; Mg 0.6–1.3; Cr 0.10; Zn 0.25; Ti 0.10; Li 2.2–2.7; Zr 0.04–0.16 [10] 8091 Si 0.30; Fe 0.50; Cu 1.0–1.6; Mn 0.10; Mg 0.50–1.2; Cr 0.10; Zn 0.25; Ti 0.10; Li 2.4–2.8; Zr 0.08–0.16 [10] 8093 Si 0.10; Fe 0.10; Cu 1.6–2.2; Mn 0.10; Mg 0.9–1.6; Cr 0.10; Zn 0.25; Ti 0.10; Li 1.9–2.6; Zr 0.04–0.14 [10] 8176 99.3 Fe 0.6; Si 0.1 electrical wire[49]Mixed list
[
edit
]
Wrought aluminium alloy composition limits (% weight) Alloy Si Fe Cu Mn Mg Cr Zn V Ti Bi Ga Pb Zr Limits†† Al Each Total 1050[50] 0.25 0.40 0.05 0.05 0.05 0.05 0.03 99.5 min 1060 0.25 0.35 0.05 0.028 0.03 0.03 0.05 0.05 0.028 0.03 0.03 0.03 0.03 0.028 99.6 min 1100 0.95 Si+Fe 0.05–0.20 0.05 0.10 0.05 0.15 99.0 min 1199[50] 0.006 0.006 0.006 0.002 0.006 0.006 0.005 0.002 0.005 0.002 99.99 min 2014 0.50–1.2 0.7 3.9–5.0 0.40–1.2 0.20–0.8 0.10 0.25 0.15 0.05 0.15 remainder 2024 0.50 0.50 3.8–4.9 0.30–0.9 1.2–1.8 0.10 0.25 0.15 0.05 0.15 remainder 2219 0.2 0.30 5.8–6.8 0.20–0.40 0.02 0.10 0.05–0.15 0.02–0.10 0.10–0.25 0.05 0.15 remainder 3003 0.6 0.7 0.05–0.20 1.0–1.5 0.10 0.05 0.15 remainder 3004 0.30 0.7 0.25 1.0–1.5 0.8–1.3 0.25 0.05 0.15 remainder 3102 0.40 0.7 0.10 0.05–0.40 0.30 0.10 0.05 0.15 remainder 4043 4.5–6.0 0.80 0.30 0.05 0.05 0.10 0.20 0.05 0.15 remainder 5005 0.3 0.7 0.2 0.2 0.5–1.1 0.1 0.25 0.05 0.15 remainder 5052 0.25 0.40 0.10 0.10 2.2–2.8 0.15–0.35 0.10 0.05 0.15 remainder 5083 0.40 0.40 0.10 0.40–1.0 4.0–4.9 0.05–0.25 0.25 0.15 0.05 0.15 remainder 5086 0.40 0.50 0.10 0.20–0.7 3.5–4.5 0.05–0.25 0.25 0.15 0.05 0.15 remainder 5154 0.25 0.40 0.10 0.10 3.10–3.90 0.15–0.35 0.20 0.20 0.05 0.15 remainder 5356 0.25 0.40 0.10 0.10 4.50–5.50 0.05–0.20 0.10 0.06–0.20 0.05 0.15 remainder 5454 0.25 0.40 0.10 0.50–1.0 2.4–3.0 0.05–0.20 0.25 0.20 0.05 0.15 remainder 5456 0.25 0.40 0.10 0.50–1.0 4.7–5.5 0.05–0.20 0.25 0.20 0.05 0.15 remainder 5754 0.40 0.40 0.10 0.50 2.6–3.6 0.30 0.20 0.15 0.05 0.15 remainder 6005 0.6–0.9 0.35 0.10 0.10 0.40–0.6 0.10 0.10 0.10 0.05 0.15 remainder 6005A† 0.50–0.9 0.35 0.30 0.50 0.40–0.7 0.30 0.20 0.10 0.05 0.15 remainder 6060 0.30–0.6 0.10–0.30 0.10 0.10 0.35–0.6 0.05 0.15 0.10 0.05 0.15 remainder 6061 0.40–0.8 0.7 0.15–0.40 0.15 0.8–1.2 0.04–0.35 0.25 0.15 0.05 0.15 remainder 6063 0.20–0.6 0.35 0.10 0.10 0.45–0.9 0.10 0.10 0.10 0.05 0.15 remainder 6066 0.9–1.8 0.50 0.7–1.2 0.6–1.1 0.8–1.4 0.40 0.25 0.20 0.05 0.15 remainder 6070 1.0–1.7 0.50 0.15–0.40 0.40–1.0 0.50–1.2 0.10 0.25 0.15 0.05 0.15 remainder 6082 0.7–1.3 0.50 0.10 0.40–1.0 0.60–1.2 0.25 0.20 0.10 0.05 0.15 remainder 6105 0.6–1.0 0.35 0.10 0.10 0.45–0.8 0.10 0.10 0.10 0.05 0.15 remainder 6162 0.40–0.8 0.50 0.20 0.10 0.7–1.1 0.10 0.25 0.10 0.05 0.15 remainder 6262 0.40–0.8 0.7 0.15–0.40 0.15 0.8–1.2 0.04–0.14 0.25 0.15 0.40–0.7 0.40–0.7 0.05 0.15 remainder 6351 0.7–1.3 0.50 0.10 0.40–0.8 0.40–0.8 0.20 0.20 0.05 0.15 remainder 6463 0.20–0.6 0.15 0.20 0.05 0.45–0.9 0.05 0.05 0.15 remainder 7005 0.35 0.40 0.10 0.20–0.70 1.0–1.8 0.06–0.20 4.0–5.0 0.01–0.06 0.08–0.20 0.05 0.15 remainder 7022 0.50 0.50 0.50–1.00 0.10–0.40 2.60–3.70 0.10–0.30 4.30–5.20 0.20 0.05 0.15 remainder 7068 0.12 0.15 1.60–2.40 0.10 2.20–3.00 0.05 7.30–8.30 0.01 0.05–0.15 0.05 0.15 remainder 7072 0.7 Si+Fe 0.10 0.10 0.10 0.8–1.3 0.05 0.15 remainder 7075 0.40 0.50 1.2–2.0 0.30 2.1–2.9 0.18–0.28 5.1–6.1 0.20 0.05 0.15 remainder 7079 0.3 0.40 0.40–0.80 0.10–0.30 2.9–3.7 0.10–0.25 3.8–4.8 0.10 0.05 0.15 remainder 7116 0.15 0.30 0.50–1.1 0.05 0.8–1.4 4.2–5.2 0.05 0.05 0.03 0.05 0.15 remainder 7129 0.15 0.30 0.50–0.9 0.10 1.3–2.0 0.10 4.2–5.2 0.05 0.05 0.03 0.05 0.15 remainder 7178 0.40 0.50 1.6–2.4 0.30 2.4–3.1 0.18–0.28 6.3–7.3 0.20 0.05 0.15 remainder 8176[49] 0.03–0.15 0.40–1.0 0.10 0.03 0.05 0.15 remainder Alloy Si Fe Cu Mn Mg Cr Zn V Ti Bi Ga Pb Zr Limits†† Al Each Total †Manganese plus chromium must be between 0.12 and 0.50%.Cast alloys
[
edit
]
The Aluminum Association (AA) has adopted a nomenclature similar to that of wrought alloys. British Standard and DIN have different designations. In the AA system, the second two digits reveal the minimum percentage of aluminium, e.g. 150.x correspond to a minimum of 99.50% aluminium. The digit after the decimal point takes a value of 0 or 1, denoting casting and ingot respectively.[1] The main alloying elements in the AA system are as follows:[51]
Named alloys
[
edit
]
Applications
[
edit
]
Aerospace alloys
[
edit
]
Parts of the MiG–29 are made from Al–Sc alloy[54]Titanium alloys, which are stronger but heavier than Al-Sc alloys, are still much more widely used.[55]
The main application of metallic scandium by weight is in aluminium–scandium alloys for minor aerospace industry components. These alloys contain between 0.1% and 0.5% (by weight) of scandium. They were used in the Russian military aircraft MiG-21 and MiG-29.[54]
Some items of sports equipment, which rely on high performance materials, have been made with scandium–aluminium alloys, including baseball bats,[56] lacrosse sticks, as well as bicycle[57] frames and components, and tent poles.
U.S. gunmaker Smith & Wesson produces revolvers with frames composed of scandium alloy and cylinders of titanium.[58]
Potential use as Space Materials
[
edit
]
Due to its light-weight and high strength, aluminium alloys are desired materials to be applied in spacecraft, satellites and other components to be deployed in space. However, this application is limited by the energetic particle irradiation emitted by the Sun. The impact and deposition of solar energetic particles within the microstructure of conventional aluminium alloys can induce the dissolution of most common hardening phases, leading to softening. The recently introduced crossover aluminium alloys[59][60] are being tested as a surrogate to 6xxx and 7xxx series in environments where energetic particle irradiation is a major concern. Such crossover aluminium alloys can be hardened via precipitation of a chemical complex phase known as T-phase in which the radiation resistance has been proved to be superior than other hardening phases of conventional aluminium alloys.[61][62]
List of aerospace aluminium alloys
[
edit
]
The following aluminium alloys are commonly used in aircraft and other aerospace structures:[63][64]
Note that the term aircraft aluminium or aerospace aluminium usually refers to 7075.[65][66]
4047 aluminium is a unique alloy used in both the aerospace and automotive applications as a cladding alloy or filler material. As filler, aluminium alloy 4047 strips can be combined to intricate applications to bond two metals.[67]
6951 is a heat treatable alloy providing additional strength to the fins while increasing sag resistance; this allows the manufacturer to reduce the gauge of the sheet and therefore reducing the weight of the formed fin. These distinctive features make aluminium alloy 6951 one of the preferred alloys for heat transfer and heat exchangers manufactured for aerospace applications.[68]
6063 aluminium alloys are heat treatable with moderately high strength, excellent corrosion resistance and good extrudability. They are regularly used as architectural and structural members.[69]
The following list of aluminium alloys are currently produced,[citation needed] but less widely[citation needed] used:
Marine alloys
[
edit
]
These alloys are used for boat building and shipbuilding, and other marine and salt-water sensitive shore applications.[70]
4043, 5183, 6005A, 6082 also used in marine constructions and off shore applications.
Automotive alloys
[
edit
]
6111 aluminium and 2008 aluminium alloy are extensively used for external automotive body panels, with 5083 and 5754 used for inner body panels. Bonnets have been manufactured from 2036, 6016, and 6111 alloys. Truck and trailer body panels have used 5456 aluminium.
Automobile frames often use 5182 aluminium or 5754 aluminium formed sheets, 6061 or 6063 extrusions.
Wheels have been cast from A356.0 aluminium or formed 5xxx sheet.[71]
Engine blocks and crankcases are often cast made of aluminium alloys. The most popular aluminium alloys used for cylinder blocks are A356, 319 and to a minor extent 242.
Aluminium alloys containing cerium are being developed and implemented in high-temperature automotive applications, such as cylinder heads and turbochargers, and in other energy generation applications.[72] These alloys were initially developed as a way to increase the usage of cerium, which is over-produced in rare-earth mining operations for more coveted elements such as neodymium and dysprosium,[73] but gained attention for its strength at high temperatures over long periods of time.[74] It gains its strength from the presence of an Al11Ce3 intermetallic phase which is stable up to temperatures of 540 °C, and retains its strength up to 300 °C, making it quite viable at elevated temperatures. Aluminium–cerium alloys are typically cast, due to their excellent casting properties, although work has also been done to show that laser-based additive manufacturing techniques can be used as well to create parts with more complex geometries and greater mechanical properties.[75] Recent work has largely focused on adding higher-order alloying elements to the binary Al-Ce system to improve its mechanical performance at room and elevated temperatures, such as iron, nickel, magnesium, or copper, and work is being done to understand the alloying element interactions further.[76]
Air and gas cylinders
[
edit
]
6061 aluminium and 6351 aluminium are widely used in breathing gas cylinders for scuba diving and SCBA alloys.[77]
See also
[
edit
]
References
[
edit
]
Bibliography
[
edit
]
Comments Off
on The Pros and Cons of Using Aluminium Metals In Construction: What You Need to Know
Aluminum metals have become popular in construction due to their cost-effectiveness and lightweight yet strong properties. They have many advantages, such as being corrosion-resistant, non-combustible, and easy to work with. However, there are also some drawbacks to using aluminum metals in construction. This article will explore the pros and cons of using aluminum metals in construction, so you can decide if they’re right for your project. It will cover the benefits and drawbacks of aluminum metals, including their cost, durability, and environmental impact. Additionally, it will provide some precautions to take when using aluminum metals in construction. By understanding the pros and cons of aluminium metals in construction, you can make an informed decision about whether or not to use them in your project.
Aluminium is a silvery-white, soft, ductile, non-magnetic, and non-ferrous metal. It’s usually alloyed with other metals, such as copper, manganese, and zinc, to increase its strength. The most common alloys are aluminum-bronze, aluminum-copper, and aluminum-magnesium. Aluminium is the most abundant metal in the Earth’s crust. It’s usually refined from bauxite, a sand containing aluminum hydroxide. However, aluminum refining is relatively energy-intensive and can produce significant greenhouse gases. Thus, aluminum is often recycled to minimize its environmental impact, with 99% of the aluminum ever produced is recycled.
As mentioned above, aluminum’s lightweight and strong properties make it a good choice for construction. Here are some other advantages of using aluminium metals in construction: – Aluminium is corrosion-resistant, meaning it won’t corrode in water or other substances. This is particularly beneficial in hydropower plants, water and wastewater systems, marine structures, and bridges. – Aluminium is non-combustible, which is beneficial in places where fire safety is a concern. This is particularly important for airports, hospitals, and hotels. – Aluminium is easy to work with and manipulate, making it a good choice for complex construction projects. – It’s relatively affordable to process and manufacture aluminum. – It’s low-maintenance, making it a good choice for use in places where the environment is harsh, such as deserts and mountains. – It’s lightweight, which makes it energy-efficient to transport and install. – It can be recycled, so it doesn’t create as much waste as other metals.
Though aluminum has many advantages, there are also some cons to using it in construction. Here are a few potential issues to consider: – As with all metals, aluminum is vulnerable to corrosion from saltwater, so it’s essential to select the right type of aluminium for marine structures. – As a soft metal, aluminum isn’t as strong as other metals, so it may not be a good choice for high-load applications. – While aluminum is a good conductor of electricity, it’s a poor conductor of heat. This can be problematic in places with high temperatures, such as in power plants, furnaces, and ovens. – It can be challenging to join aluminum with other materials, making construction more complicated. – There are concerns about how the extraction and refinement of aluminum affect the environment.
Aluminium is an affordable and abundant metal, which is why it’s so prevalent in construction. Though it’s significantly less expensive than other metals like steel, it’s generally more affordable than other materials such as concrete. The price of aluminum depends on the type of alloy used, the aluminum grade, and the purchase location. On average, the cost of 1 tonne of aluminum is $380. It’s essential to consider the total cost of a project and its lifespan when deciding whether or not aluminum is the best choice. For example, a concrete structure may cost more to build, but it could last for decades and be worth the extra expense.
Though aluminium has many advantages, it’s important to note that it isn’t the strongest metal. It may not be the best choice for high-load applications. Aluminium is known to lose strength when exposed to saltwater and corrodes when exposed to chloride. Most aluminum alloys are unsuitable for outdoor use, so they must be protected from the elements. Because of these factors, aluminum is best suited for low-load applications, such as residential construction, fences, railings, and walkways. It’s also a good choice for places where corrosion and rust are a concern. For example, aluminum is a good choice for water and wastewater systems, marine structures, and bridges because it’s resistant to corrosion. It’s also a good choice for fire escapes and ladders because it doesn’t catch fire. However, keeping aluminum from high heat and electricity sources is essential.
Aluminium is a controversial material; some argue that it’s better than other materials, while others claim it’s worse. Let’s start with the positives. Aluminium is a sustainable resource that can be recycled infinitely. It’s also a relatively clean and energy-efficient metal to refine. However, it requires a large amount of electricity to produce. Some experts believe that the energy required to produce aluminium is higher than the energy required to produce other metals, such as iron. When produced, aluminum releases greenhouse gases, including carbon dioxide, nitrous oxide, and sulphur dioxide. It’s also responsible for releasing fluorine, which is harmful to the environment, and acid rain, which can damage crops and buildings. When discarded, aluminum creates toxic sludge and dust, polluting the air, water, and soil.
Because aluminium is a soft metal, it’s important to protect it from abrasion and corrosion. When designing projects using aluminium, it’s essential to consider the environment and nearby materials. For example, if you’re using aluminum on a bridge, you may want to consider the amount of traffic and the size of the vehicles passing over it. You may also want to consider the nearby materials; for example, if you’re using aluminum in a marine structure, you may want to stay away from saltwater. Additionally, aluminum must be kept away from sources of high heat. In general, it’s best to keep aluminum away from humidity, water, and dirt.
Aluminium is a popular choice for construction due to its lightweight and strong properties. It’s easy to work with and can be manipulated into many forms. Aluminum has many advantages, including its low cost, durability, and corrosion resistance. However, aluminum does have some drawbacks, including its low strength and high environmental impact. When designing a project using aluminum, it’s important to consider the environment and nearby materials. It’s also important to take precautions to protect the aluminium from corrosion and abrasion.
Who are we?
Welcome to your one-stop shop for everything aluminum! We are proud aluminum enthusiasts and suppliers in Canada and the USA, offering a wide selection of surplus, premium colour Aluminum Coil, raw and customized anodized Aluminum sheets, vibrant coloured Aluminum wire and even convenient pre-cut rolls of Aluminum Foil. Our warehouse is full of these materials, ready to ship today – so start building or crafting with our quality products now!