A bilge pump is one of the most crucial safety features of a boat. Without a bilge pump, excess outside water or leaks can cause a boat to flood or sink. Consequently, these pumps save lives, making them essential to any vessel. There are many types of bilge pumps on the market, and each of them discharges water with a different method than the others. Because of this, selecting a bilge pump for your boat or marine application can be difficult. Below you can find information about what bilge pumps are, how they work, the types of bilge pumps, and how to perform maintenance on your bilge pump.
Link to MIC
What is a bilge pump?
A bilge pump is a marine pump designed to clear water out of the bottom of a boat&#;s hull, also known as the bilge. This water may be the result of rain, leaks, splashes, cleaning, or coolers that drain into the bilge. Bilge pumps are rated by the volume of water they can remove in one hour, and each type of pump possesses different ratings at which they are available. These pumps can prevent small leaks from sinking a boat, giving more time for a diagnosis and resolution to be reached. Even for large-scale leaks, bilge pumps can buy more time for help to arrive.
Learn more: How to choose the right bilge pump for your boat
How does a bilge pump work?
Automatic bilge pumps use a float switch to activate the pump once water pools above a predetermined level. Once the switch is activated, the pump kicks on to remove the water from the bilge until it is dry. Once the bilge is free of water, the switch deactivates the pump until the water reaches the activation level again. This feature prevents the pump from running constantly while also protecting the boat from built-up water. Some bilge pumps use rotational energy to force water out of a boat, and others use suction to draw water in and push it out. While some older boats use manual bilge pumps, modern boats make use of automatic bilge pumps. Learning how each pump type deals with water can help you select the best one for your boat.
Where are bilge pumps located?
Depending on the type of bilge pump in a boat, the pump can be located at the bottom of the bilge or outside of it. Submersible bilge pumps are always located at the lowest point of the bilge because they can only operate underwater. Diaphragm bilge pumps are installed above the bilge away from the water. The hoses for these pumps are lower than a submersible pump can be installed, so they can remove more water than a submersible pump. As a result, these are often referred to as &#;drying pumps&#; and are often used in conjunction with a submersible pump.
The most important factor for the location of a bilge pump is its accessibility. Bilge pumps must always be accessible for routine maintenance, inspection, and testing. If your bilge pump is located in a hard to access area, consider relocating it to a more accessible one.
Types of bilge pumps
There are three main types of bilge pumps: centrifugal, electric diaphragm, and reciprocating. Each type has advantages and disadvantages over the other pumps for certain boat sizes and applications. Some also come in manual configurations that are ideal for small recreational boats.
Centrifugal bilge pumps
Centrifugal bilge pumps are submersible pumps that use an impeller to increase the kinetic energy of incoming water so that it can be pumped out. When water enters the impeller, the impeller&#;s rotational force increases the water&#;s speed. Around the impeller is a diffusion ring with fixed blades. These blades convert the speed of the water into pressure, allowing the water to be pumped out of the boat. Unlike diaphragm and reciprocating bilge pumps, centrifugal pumps are not self-priming, and they must be submerged to operate. The simple design of these pumps makes maintenance simpler than for other pump types.
When water is discharged from the centrifugal pump, the pressure inside the casing drops to draw water into the eye of the impeller. This means the pump must be primed with water before it can draw water in on its own. This feature also prevents centrifugal pumps from removing all water from a boat&#;s bilge. To remove all water, a diaphragm or reciprocating bilge pump should be used.
Centrifugal bilge pumps can handle large volumes of water, and they are typically less expensive than other pump types. Sizeable marine operations, such as large ships, use centrifugal pumps with multiple impellers to discharge the high volumes of water that the boat intakes.
Advantages of centrifugal bilge pumps
Disadvantages of centrifugal bilge pumps
Electric diaphragm bilge pumps
Electric diaphragm bilge pumps are self-priming positive displacement pumps that use a diaphragm to draw in and displace water. These pumps create suction to draw in water as the diaphragm opens and discharge it when the diaphragm closes. Diaphragm pumps are better at pumping water uphill than centrifugal pumps, and as a result, they can remove all water from a boat&#;s bilge. Unlike other pumps, diaphragm bilge pumps can be mounted away from the bilge, making them less prone to damage than other pump types. Consequently, diaphragm bilge pumps have a longer lifespan than most centrifugal and reciprocating pumps. There are multiple types of diaphragm bilge pumps, including single-diaphragm and double-diaphragm configurations.
Single-diaphragm pumps contain one diaphragm that draws water in and discharges it as the diaphragm moves around. This is the standard design for diaphragm pumps, but the flow rate is not as high as double-diaphragm pumps.
Double-diaphragm pumps have two connected diaphragms that move in conjunction with each other. As one diaphragm opens to let water in, the other one closes to let water out. This allows for more water to be displaced by the pump and generates a more consistent flow rate.
Electric diaphragm pumps cannot handle debris entering the pump&#;s chamber. Any debris that gets stuck between the diaphragm and the pump&#;s walls has a high likelihood of damaging the pump. A filter must be installed before the pump&#;s inlet valve to ensure debris cannot enter. Diaphragm bilge pumps cannot handle the large volumes of water a centrifugal pump can. Consequently, diaphragm pumps can only be used on small to medium-sized boats and other small marine applications.
Advantages of electric diaphragm bilge pumps
Disadvantages of electric diaphragm bilge pumps
Reciprocating bilge pumps
Reciprocating bilge pumps, also known as piston bilge pumps, are self-priming positive displacement pumps that are more effective at uphill pumping than centrifugal pumps. These pumps draw water in on one side of the piston and discharge it from the opposite side. Both sides of the piston contain a suction valve and a discharge valve. As the piston moves up, the top suction valve opens to allow water in. Simultaneously, the upper discharge valve remains closed, and the lower discharge valve opens to allow the water beneath the piston to escape. When the piston moves down, the lower suction valve opens, the bottom discharge valve closes, and the upper discharge valve opens. The water that was previously drawn in above the piston is now discharged.
Reciprocating bilge pumps are even less tolerant of debris than diaphragm pumps. When debris enters the pump, it lodges between the piston and the pump&#;s wall. This can clog the discharge and suction valves and lead to pump failure. To counteract debris, a filter must be installed in front of the suction valve. In addition, reciprocating bilge pumps are not capable of displacing as much water as other pump types. As a result, reciprocating bilge pumps can only be used for small boats and other marine applications.
Advantages of reciprocating bilge pumps
Disadvantages of reciprocating bilge pumps
Manual bilge pumps
Manual bilge pumps are hand water pumps used for non-motorized boats. Most manual bilge pumps output a maximum of 20 gallons per minute, and they should not be used for motorized marine applications. Typical applications for these pumps include kayaks, canoes, and dinghies.
Advantages of manual bilge pumps
Disadvantages of manual bilge pumps
Learn more about water pumps: Well pumps | Rotary vane pumps | Grundfos Scala pumps | RV water pumps
Bilge pump maintenance
Performing regular checkups on your bilge pump is critical for both your safety and the lifespan of your marine pump. Maintenance not only saves money on a new pump, but it can also spare you from costly boat repairs caused by flooding. There are several checks you can perform to extend the life of your bilge pump.
1. Test the pump
Before heading out on the water, you should ensure that your bilge pump is working properly. While this may seem like a mundane task, it can save you from headaches and danger should the pump fail while on the water. To test the bilge pump, pour a few gallons of water into the bilge. If the pump activates and removes the water, the pump is working correctly. Should the water remain stagnant in the bilge, either there is not enough water to activate the pump or the pump needs maintenance. If your pump is not working properly, do not go out onto the water.
2. Check the wiring and float switch
While on the water, you should be able to hear the bilge pump running. If you hear the pump running constantly, either too much water is getting into the bilge, the switch is faulty, or the wiring is incorrect or broken. If your pump is running constantly, inspect all wiring for corrosion or breaks. If the wiring appears functional, ensure the float switch is free of debris. If both the wiring and the float switch operate correctly, check for leaks or other causes of excess water in the bilge.
3. Clean the pump
Water that makes its way into the bilge is often full of unwanted gunk such as algae, debris, and dirt. While some bilge pumps can deal with these nuisances, they can wear down a pump over time. Bilge cleaners break down built-up sludge on the inside of a pump to keep it running smoothly. They also work while your boat is on the water, so you do not have to worry about rinsing the pump before heading out. In addition to using a bilge cleaner, you should wash the outside of the pump about once every month during the seasons your boat is in use.
4. Check the outlet hose
Outlet hoses are durable, but they should still be regularly inspected for damages and clogs. If only a small amount of water comes out of your hose, it is likely clogged or there is a problem with the battery. If the voltage on the battery is normal and the hose is not clogged, the issue most likely lies within the pump itself.
5. Check the impeller
For centrifugal pumps, the impeller&#;s inability to rotate is a clear sign of a faulty pump. To test the impeller, shut the power off to the pump and unmount it from the bilge. Attempt to turn the impeller with your hand. If it does not turn and it is free from obstruction, the pump needs to be replaced.
6. Check the filters
The filters that prevent debris from building up in the pump can easily become overwhelmed if not regularly cleaned. Before going out on the water, ensure that all debris is removed from the filters.
When should a bilge pump be turned on?
If you have an automatic bilge pump with a float switch, the switch will automatically signal the pump to turn on and off. If your pump does not utilize a float switch, you will need to watch the water levels in the bilge and switch the pump on when it needs to be emptied. Submersible bilge pumps cannot run dry, so if you notice the pump remains on when the bilge is drained, there may be a problem with your float switch or pump.
How long do bilge pumps last?
An average bilge pump lasts around three to five years. If well maintained, it can last longer, but you will need to ensure the pump is safe each time you go out onto the water. One sign that a bilge pump is reaching the end of its life cycle is a poor flow rate. If a pump is not clogged and it outputs lower volumes of water than normal, it likely needs to be replaced.
Do I need a filter for my bilge pump?
A bilge pump inlet screen can protect your bilge pump from damaging debris. These screens are an inexpensive way to avoid an expensive accident not only to the pump, but potentially the entire boat. Inlet screens are also low maintenance. Before heading out on the water, check the screen and remove any debris to avoid clogging.
If you have any further questions, please do not hesitate to contact us.
Whether you&#;re working on a recreational boat or a giant cargo ship, you should never head out to sea without a bilge pump. Without these, there are so many things that could go wrong.
That said, the bilge pump requirements for large vessels and smaller ships are vastly different.
In this article, you&#;ll get a comprehensive look at marine bilge pumps for both large ships and smaller boats:
By the end of it, you&#;ll know everything you need to know about marine bilge pumps.
Bilge pumps are a type of marine water pump found on both large and small ships. They are responsible for removing water accumulating bilge wells and throwing it overboard.
It&#;s impossible to stop water and oil from collecting in your bilge wells (the bottom-most part of a boat).
In large craft, these liquids usually come from machinery spaces or drainage systems. While on smaller boats, anything from rain to big waves can flood the bilge well.
The primary function of all boat bilge pumps is the same. However, these come in a variety of sizes, types, and capacities.
There are automatic bilge pumps, and there are manual ones. There are small plastic boat bilge pumps for boats, and there are heavy-duty cast iron ones for ships.
Choosing the right one for your ship will depend on several factors, which we&#;ll have a look at below.
Before that, it&#;s essential to know why bilge pumps are so important.
Bilge pumps have been around since antiquity. These were the only pumps ocean vessels carried in the old days &#; showing how essential they are to seafaring.
Modern ships may have numerous pumps on board, but the bilge pump is still one of the most vital ones.
Here are three reasons why every boat needs a marine bilge pump:
Leakage, drainage, and washing down fluids all find their way to the bilge wells of ships. If left unchecked, these wells will eventually overflow and spill into the engine room. And that can cause a lot of problems.
If the oily water rises, it may get to machinery and damage them. Also, if one compartment floods, this will affect the balance of the boat.
That&#;s why in ships, emptying the bilge wells is vital.
For recreational boats, the risk is even higher. Without deep bilge wells, all it takes is a little excess water to get to your boat&#;s electronics. Heavy rain or big waves may be all it takes to destroy your boat&#;s system.
But with a working bilge pump, you&#;ll never have to worry about flooding.
Most boat bilge pumps come with an automatic float switch. This switch turns the pump on whenever water rises above a certain level. This way, you don&#;t always have to check your bilge.
Aside from the daily role of clearing bilge wells of water, a bilge pump can also be a life-saver in emergencies.
If your ship has a small puncture and water is rushing in, a bilge pump can spit this water out faster than it comes in (depending on the hole&#;s size and your pump&#;s GPM).
The removal of the incoming water allows you to repair the hole or make an emergency docking. Note: You should never rely on your bilge pump for staying afloat. If your boat has a hole, repair it immediately.
Installing a designated emergency bilge pump with the highest capacity possible is highly recommended. You can also use ballast and firefighting pumps to help pump out the water in case of an emergency.
If the hole is too large for your marine bilge pump to handle, it can at least buy you enough time to abandon ship safely.
It&#;s not only unwise to venture into deep seas without a marine bilge pump, but it&#;s also illegal.
Maritime laws are strict on ensuring vessels have an excellent bilge system for emergencies &#; especially on passenger ships.
Generally, the larger your ship, the more pumps you are required to have. You&#;ll also need more pumping capacity:
Passengers: Vessel Length: Bilge Pumps Required: Minimum Capacity Required: Less than 49 26-65 ft. (7.9-19.8 m) 1 power pump & 1 portable hand pump or&#; 10 GPM &#; 1 fixed hand pump and&#; 10 GPM &#;1 portable hand pump 5 GPM < 26 ft. (7.9 m) 1 portable hand pump 5 GPM Over 49 + Ferry Vessels < 65 ft (19.8 m) 1 power pump and&#; 25 GPM &#;1 portable hand pump 10 GPM Any Number > 65 ft (19.8 m) 2 power pumps or more (depending on design) 50 GPMChart from law.cornell.edu.
Furthermore, it&#;s not enough just to have the pumps. They also have to be reliable.
For large vessels, getting a bilge pump that is ABS certified will ensure you&#;re complying with national and international regulations.
Not all boat bilge pumps are the same. Aside from size and capacity, there are also different types. The four most common types are:
These bilge pumps use different methods to get bilge water overboard. And they all have their pros and cons.
If you learn how these pumps work and their strengths and weaknesses, you will have an easier time selecting the right one.
Centrifugal types are the most widely used. They are famous for their high capacities, simple design, ability to handle small debris, and low cost.
In large ships, bilge pumps are almost exclusively centrifugal. When you need to move large quantities of water, centrifugal is the best option.
However, these need priming to operate. Before a centrifugal pump can move any water, you need to fill it with water first because of how it works.
Centrifugal pumps move water by turning rotational energy into kinetic energy. Inside the pump, a spinning impeller pushes water into the discharge. This creates low pressure in the pump, which sucks more water in.
For centrifugal pumps to work, there are two critical components: the impeller and the volute casing.
The impeller is a disk with vanes curving outwards. A motor spins the impeller at incredible speeds, and the vanes use centrifugal force to push incoming water to the casing sides.
The volute casing has a snail shape, starting narrow and gradually getting wider towards the discharge. This design builds pressure and forces all the water out through the discharge instead of turning around the casing.
When the water leaves the discharge, this creates low pressure within the casing, which pulls more water into the pump. Centrifugal pumps need priming to work for this reason.
Because of this, you can never remove all bilge water with a centrifugal pump. There will always be some leftover which will need another type of pump for removal.
For big ships, we recommend getting a self-priming centrifugal pump. These can separate the air inside the casing from the water. The water circulates in the pump, but the air discharges &#; creating low-pressure, which pulls in more water until the pump is full of water.
There are several types of centrifugal pumps. The two common ones are submersible and horizontal bilge pumps.
Submersible bilge pumps are for smaller vessels. They are entirely waterproof and go straight into the bilge well.
Horizontal bilge pumps are the most powerful option for ships. Instead of going into the bilge well, these pumps are strong enough to suck the water out through pipes.
Because the pump isn&#;t inside the bilge well, horizontal bilge pumps are versatile. You may also connect them to the ballast system on your ship.
Pros:
Cons:
Another common type of bilge pump is the diaphragm pump.
Diaphragm pumps are a type of positive displacement pump. Unlike centrifugal pumps, these aren&#;t typical on large ships. Their capacity isn&#;t as high as centrifugal types, and they also aren&#;t very good at handling debris.
For more information, please visit bilge hose.
However, for small and medium-sized boats, these offer several advantages.
For one, they don&#;t need any priming. Diaphragm pumps can run completely dry, whereas centrifugal pumps will get damaged. Because of this, diaphragm pumps can remove all the water in the bilge.
Diaphragm pumps also have an easier time pushing or pulling water upwards. Where a small centrifugal pump might have a hard time removing water from deeper bilges, a diaphragm pump will have no problem.
Diaphragm pumps work by using a diaphragm and check valves. The diaphragm pulls up, creating a vacuum in the pump that sucks water (or air) through the inlet check valve. When the diaphragm presses down, this forces the water out through the outlet check valve.
Because a diaphragm pump can also pull air, you don&#;t have to place them close to the bilge water. Putting them high above the bilge won&#;t need priming or as much power as a centrifugal pump in a similar position would.
The three common types of diaphragm boat bilge pumps are single-diaphragm, double-diaphragm, and manual.
Single-diaphragm is the standard design. They have a single diaphragm pulling and pushing the liquid around.
Double-diaphragms have two diaphragms placed parallel to each other in separate chambers. A rod connects these two diaphragms.
Compressed air takes turns entering each chamber &#; pushing that diaphragm closed while at the same time pulling the other open.
This design is more efficient than single diaphragms. It also creates a steadier flow of water.
Manual diaphragm pumps are not electronically powered. Use a lever to pull the diaphragm open and push it closed manually. These have the advantage that they work even when your electrical system is down.
Having one manual pump is required in most smaller vessels.
Pros:
Cons:
Like diaphragm types, reciprocating (or piston) bilge pumps are also a positive displacement pump.
They can run dry, remove all boat bilge water, and have an easier time pumping vertically than centrifugal types.
These can also work with high viscosity liquids. That is why some large ships use piston pumps to get rid of sludge in their bilge wells.
However, even the most powerful reciprocating type can&#;t move as much water as centrifugal pumps.
Reciprocating types are also bad at dealing with debris &#; even worse than diaphragm pumps. Installing a filter at the suction hose is a must.
Reciprocating pumps work by using a piston and check valves. The piston pulls up, creating a vacuum in the pump that sucks water (or air) through the inlet check valve. When the piston presses down, this forces the water out through the outlet check valve.
Because the piston is air-tight, you also don&#;t have to put it inside the boat bilge. However, reciprocating boat bilge pumps cannot tolerate debris. Debris will lodge in between the piston and the pump&#;s walls, jamming or destroying the pump.
Pros:
Cons:
Flexible impeller pumps may look similar to centrifugal types, but they are very different from one another.
Instead of a solid impeller with vanes, flexible impeller pumps use a rubber impeller squeezed by the casing to give it its curved shape.
Flexible impellers are another type of positive displacement pump. They are self-priming and can remove all the water from the bilge well. They are also capable of carrying solids and debris.
However, unlike diaphragm and reciprocating types, you should never run a flexible impeller pump dry. Without water, the friction between the impeller and casing will burn the rubber impeller.
Flexible impeller pumps use a rubber impeller and a cam to function. As the spinning impeller meets the cam, it bends, squeezing its trapped water out the discharge. When the impeller leaves the cam, negative pressure creates a suction that pulls in more water.
Because of their material and simple design, flexible impeller pumps are affordable. Their design also allows you to run them in reverse should you want to.
Pros:
Cons:
The ocean is not the place to find out your pump doesn&#;t cut it. Taking the time to choose the right pump can spell the difference between sinking and saving your ship.
Also, knowing what you&#;re looking for ahead will ensure that you don&#;t spend a lot of money on a pump that doesn&#;t fit your everyday bilge pump needs.
However, with so many different types and so many GPM options, choosing the right one can be challenging.
There are several things you need to consider before buying a bilge pump:
Between centrifugal, diaphragm, reciprocating, and flexible impeller pumps &#; which one will suit your boat the best?
That depends on the type of boat you have and the condition of your bilge.
Large vessels almost always use centrifugal pumps. These boats need the high capacities that only these can deliver.
You may use other types of pumps, such as diaphragms, for thoroughly clearing out the bilge well. But for bilge transfer and emergencies, nothing can match the output of centrifugal bilge pumps.
You can also connect these horizontal pumps to elaborate pipe systems that use valves to control where the water comes from and where it goes.
For smaller boats, you have more options. The two most popular types are centrifugal and diaphragm.
Submersible centrifugal pumps may have difficulty pushing water up if you place the discharge hose high above the bilge. But they&#;re also cheap, easy to maintain, and can move a lot of water. If you set up your bilge correctly, these will be perfect for you.
Diaphragm types are more expensive. However, you don&#;t have to place them down in the dirty bilge for them to work. They are more convenient to set up and clean. Plus, they can remove all the water in the bilge.
Reciprocating pumps aren&#;t quite as popular. These are incredibly efficient when dealing with high-viscosity liquids like sludge, which isn&#;t common in small boats.
Flexible impellers are cheaper than the diaphragm and reciprocating types. However, you&#;ll have to change their soft impeller now and then.
GPM, or gallons per minute, refers to your bilge pump&#;s pumping performance or flow. The higher the GPM, the faster your bilge pump can drain your boat bilge. Generally, the bigger your pump, the more GPM it will have.
A good rule of thumb is to get the highest GPM that&#;s reasonable for your boat. Your bilge pump is what will save you when you&#;re sinking. That&#;s why you&#;ll want one with as much GPM as possible.
All ships are different &#; there is no one-size-fits-all when it comes to GPM. The law chart above only shows the minimum GPM required. In practice, you&#;ll need much more GPM if you want to be safe.
That&#;s why you should get the biggest bilge pump you can get.
One misconception a lot of people have is that smaller boats can get away with a small pump. Smaller boats will need the largest pump they can get since their small hulls will fill up with water much faster than large ships.
That said, you also have to be reasonable. Smaller boats won&#;t have space for an enormous and heavy pump. Consider the pump&#;s size and weight when choosing because it might be too bulky for your boat.
Aside from GPM, you also need to check the total head of your bilge pump.
Centrifugal pumps have a hard time pushing water up vertically. To know if your pump can handle your discharge pipe&#;s height and length, calculate the total head and compare it to your pump&#;s head rating.
To get a basic idea of how much head you need, use this equation:
Elevation + Pressure + Friction Loss = Total Head
Elevation refers to the total vertical rise in feet. If your discharge pipe&#;s end is 20 ft above your pump, your elevation is 20ft (regardless of the pipe&#;s overall length).
Pressure refers to the amount of pressure of the fluid in the pipe. Use PSI to measure this, then convert it to head feet (1 PSI = 2.31 Head Feet).
Friction Loss refers to the loss of flow due to friction in your pipes. The equation for this is quite complicated, but there are several calculators you can use online for this.
Add those together, and you&#;ll get your total head. You should get a pump that reaches or exceeds that total head.
Manufacturers rate a pump&#;s GPM in ideal conditions, where the water is right next to the pump, and the discharge is horizontal. A 10GPM pump will empty 10 gallons of water in a minute with these conditions.
However, in practice, pumps move far less GPM than they are rated. And this can be a problem for smaller boats.
You may think that your 10 GPM pump is strong enough to eliminate all nuisance water and maybe even save you from sinking. In reality, your 10GPM pump might only be moving at 3GPM.
The GPM goes down because there is about a 20% capacity drop due to voltage (small boat bilge pumps are tested at 13.6 volts while most marine batteries only run at 12), 30% for head height, and 20% from hose resistance.
Those numbers are estimates. But you should consider that unless you have the ideal setup, you may only be getting 30% of your pump&#;s rated GPM. So don&#;t take chances. Get the highest capacity pump your boat can handle to stay safe.
Unless you have a giant ship, a manual bilge pump is vital. If water gets to your electric system, your bilge pump will shut off. The only way to save your boat or buy time then is by using a manual bilge pump.
Make sure your manual bilge pump is easily accessible and can operate from a comfortable position. Pumping water off your boat bilge is tiresome, so you don&#;t want to be cramped or in an awkward position while using your hand pump.
For big ships, if your motor-driven pumps fail, you&#;re better off abandoning the ship than attempting to clear the water with a manual pump.
You can have the highest capacity marine bilge pump around, but it won&#;t save you unless you install it properly.
Nowadays, bilge pump systems on ships require inspection for compliance. However, too many small boaters still unknowingly make mistakes when installing bilge pumps.
Here are some general principles to follow when installing a marine bilge pump.
Every watertight compartment in your vessel needs a bilge pump or a pipe connected to a bilge pump. Every room in your boat where water can&#;t flow to the next one needs a bilge pump.
In large vessels, pipes from every compartment connect to three, four, or more bilge pumps. The draining of every area without installing a pump in each one is possible because of this.
However, that is only possible because ships use large and powerful bilge pumps with elaborate piping systems. For smaller boats, you should keep one (or two) bilge pumps in every watertight area.
Boat bilge pumps should be at the lowest possible point possible. However, the discharge shouldn&#;t be too close to sea level (to avoid siphoning).
For ships, you&#;ll want at least one pump on the starboard and one on the port. You also shouldn&#;t group the marine bilge pumps close to each other. In an emergency, you don&#;t want the bilge pumps together because they will all get flooded.
Bilge pumps in ships use electric motors, the ship&#;s engine, or emergency generators for power. An emergency bilge pump should always have its own power supply.
In smaller boats, follow the manufacturer&#;s directions as closely as possible &#; from the battery voltage right down to the wire gauge. Doing this will clear up a lot of potential problems you may encounter.
There are several ways to switch on a bilge pump. You could turn them on manually in the engine control room (for ships) or connect them to the battery (for small boats). However, the ideal setup has automatic switches in place.
Float switches are simple devices that turn your bilge pump on when the water reaches a certain level &#; and turns them off once the water descends. Installing one of these is excellent since you won&#;t have to monitor your boat&#;s bilge water levels all the time.
Some ships need to turn on their bilge pump manually. To help with this, you can install bilge alarms to go off whenever the water has risen to a certain level. This way, you don&#;t have to go and check now and then.
Having a float switch is especially crucial if you&#;re using a centrifugal pump. Centrifugal pumps can&#;t run dry. If they do, they&#;ll get destroyed. That&#;s why having them switch off automatically before the water has fully descended is crucial.
Ensure your switch is high enough that when the excess water in the pump flows back into the bilge, it won&#;t reach the switch.
When installing a float switch, make sure it is in a place that can&#;t get caught while rising. If it gets stuck, it won&#;t trigger your pump to start, and you may flood your boat.
That&#;s why you should never rely on automatic switches. Check your bilge well now and then to make sure your pump is working correctly.
Other types of automatic switches include contact switches, air chamber switches, and magnetic read switches. All of these perform the same function as float switches.
As mentioned earlier, large vessels have elaborate piping systems that connect to the bilge pumps. Valves control which pipes are running and which lines are standing by.
Each compartment in the ship must have a bilge pipe. These pipes connect to the bilge manifest, which then takes the bilge water to the pump.
For smaller boats, hoses are used instead of pipes. To lower the hose friction, get a smooth hose. Corrugated hoses increase friction and will further reduce your pump&#;s GPM.
Follow the manufacturer&#;s directions when choosing hose size and length.
A bilge pump takes bilge water and discharges it overboard. However, in ships where oils and other fluids mix with water in the bilge, this water must go through a filtering process first.
From the bilge pump, the bilge water pumps into several bilge tanks, where gravity separates oil and water.
The oil is taken to the incinerator, while the water (which should be under 15ppm) goes overboard. Ships can do this entire process automatically with switches and sensors.
However, in emergencies, the whole bilge water management system is bypassed. All water goes straight overboard regardless of oil content. But this is only legal in emergencies &#; otherwise, under MARPOL regulations, the water pumped overboard must be under 15 ppm to prevent pollution.
One problem that is common in smaller boats is siphoning. The discharge should be well above the waterline. However, sometimes, this is not possible. To avoid siphoning, install a siphoning break on your hose or pipe.
Though centrifugal pumps can handle some debris, it isn&#;t ideal since it increases pressure and slows down the flow. That is why installing mud boxes on bilge pipes is a good idea.
Mud boxes or strum boxes filter out debris from getting to the pump.
In ships, bilge pipes must have non-return valves. These valves prevent liquid in the pipes from flowing back into the bilge well.
Priming your centrifugal bilge pump is slightly different for each pump. But the general method is the same:
Refer to your pump&#;s manual to know the exact procedure.
Of course, if you have a self-priming centrifugal pump, your machine will do this independently.
If you set up everything correctly, nothing should go wrong. You won&#;t have to worry about problems, especially if you are using a centrifugal-type pump.
However, there are a few things you need to check once in a while.
To ensure that your pump is running correctly and efficiently, perform the following checks:
Aside from the regular checks, perform these maintenance tasks once in a while:
A dirty boat bilge is especially harmful to smaller boat bilge pumps. Dirt can clog up the filter and prevent water from getting in.
Make sure your boat bilge is free from dirt and other debris by cleaning it now and then.
You may find your filter already clogged with dirt and debris. If so, clean it up immediately. If you have mud or strum boxes, it&#;s also essential to check them once in a while.
One of the last things you want is for your automatic switches to fail. In smaller boats, one failure may allow the water to rise to the wiring of your boat. In ships, switch failure will get oily water into the dry-compartments.
Either way, checking your automatic switches is a must. If you have bilge alarms in place, also test those.
When it comes to choosing a marine bilge pump, reliability is of utmost importance. Your bilge pump is your last line of defense. If it fails, your ship is going down.
The best way to ensure a high-quality and reliable marine bilge pump is to choose a trusted brand.
For small boats, brands like Rule Industries, Attwood, Albin, and Johnson Pump make great boat bilge pumps. You can buy these at your local marine supply, or you can also get them online.
However, buying a marine bilge pump is not as easy as walking into a store or placing an order online for large ships.
When the demands are high, you need a pump that&#;s tailor-made to fit your ship&#;s needs. You need a pump that can stand up to every test and every international regulation. You need a pump you can trust to save your ship when things go wrong.
For high-quality, custom-built, ABS certified pumps, choose Carver Pump.
Carver Pump is a company dedicated to building American-made pumps with military-grade precision to accommodate highly developed specifications.
The ocean is no place to find out your pump does not make the grade. Trust your shipboard services to Carver Pump, the industry leader in shipboard centrifugal pumps.
Want more information on marine exhaust hose? Feel free to contact us.