Purlin is one such material that helps create roofs that are strong and durable. Purlin is a solid horizontal beam used mostly in steel building systems to provide structural support for roofs. They are supported either by the rafters or by the buildings walls. Purlins are extremely important because they provide the roof with the required support, strengthen and reinforce the building framework and add additional aid between the spans of individual framing bays.
Roofing is an important part of the construction, it needs to be carried perfectly and managed with quality. Rooftop damage can include leakage, damp wall, and insect growth such as moths, etc. It contributes to the growth of moisture, cold, etc like problems. Because of these factors, after considering all your architectural/structural requirements, it is important to choose purlin wisely from the best purlin manufacturers. Therefore, here are a few tips for choosing the best purlin for roof framing.
Purlins hold tons of large roof decks and are supported by the framework of rafters or walls and steel beams. Purlins material defines the design of the building and keeps the site safe and environmentally sustainable, along with its robust and sturdy design. The recycled steel, superior tensile strength, highly durable, abrasion & corrosion resistant are a major part of the metal trusses.
Also Read: Important Roofing Accessories That You Need For Your Roof
This is one of the big decisions you have to take to take into account the construction requirements and the quality of roofing. C type & Z Type are the major types of Purlin available. C and Z purlins are more common and are called so because in a square form they look like the corresponding letters.
C Purlin: C Purlins are used as wall panels, rafters, floor joints and wall studs.
Z Purlin: Z Purlins are similar to the Z alphabet and are also known as Z Purlins. This shape tends to overlap the joint with the purlins and is better and more strong than the C purlins.
It is mandatory that they should be installed horizontally under metal roofs when it comes to Purlins roofing installation. On top of the roof rafters, they should be mounted with a felt underlay or vapour barrier installed on top. Purlins measure 2 by 4 feet, much like metal roofing, are installed. To provide the roof with additional protection and also provide the end panels and drip edge with a nailing surface.
Also Read: 5 Advantages of Metal Decking Sheets
Note that you cant cut by using the heat when you want to install purlin. For purlin material, both the welding and heat cutter are not appropriate. The durability and high tensile strength of purlin may be compromised by heat. As we all know, in both welding and heat cutting processes, heat is generated that affects the properties of materials that are the reason for its high tensile quality and rigidity.
Not all Purlin panel materials are the same. In metal manufacturers, choose the best purlin that can provide you with the best material quality and a genuine, renowned and trusted. Roofing installation is costly and requires an extra-large amount, so you have to take every decision with extra caution and choose the best possible manufacturer that can provide you with the best purlin quality.
In India, Bansal Roofing Ltd manufactures purlin that provides high-quality roofing material that is perfectly mounted and used for a longer period of time. They have various materials and designs on the basis of your budget and requirements. According to the weather condition of your location, Bansal will help you determine the purlin sizes and length. It is convenient as Bansal also offers free consultation and 24/7 service.
Sunnyda Z beam steel is very useful and stronger to use for roofing applications. Z beam steel is very useful for your building projects. It is capable to support your frames and roof structures that provide the best protection for your building projects from any weather conditions.
Sunnyda Z beam steel is attainable at different dimensions. There many advantages when choosing Z beam steel for your business. It is great for your business since Z beam steel is popular and durable for building constructions. We ensure that your customers will choose these beams for building their homes.
Sunnyda Z beam steel is a cold-formed known as the HFB or the hollow flange beam and a resistance. There are many sizes that your business and applications will suit from. We have 1.2 to 2.5mm of Z beam steel thickness that could offer for your business.
Z beam steel can carry up to lbs of weight that can be assembled horizontally and vertically. It is manufactured in the best quality steel.
We are popular in manufacturing and supplying cost-effective ideal building materials. Sunnyda is capable to export products from different places to Belgium, Dubai, South America, and many more places.
We are a professional and experienced manufacturer in China of steel structure, prefabricated container house, steel structure buildings, trailer house, and sandwich panel that ensure the roof applications durably. We have 60 employees and expert 12 architects that guide the whole process.
Whether you need Z beam steel for industrial, or any applications, we are capable to sustain your special needs.
Our Z beam steel offers plenty of years of life span and 1 year of warranty. We ensure that the Z beam steel is quality checked through our control team. Sunnyda has a complete device for any process just to support your needs from designs, dimensions, and many more special requirements.
We can help you save your budget and expand your business faster than you imagine. There are many people who owned the business who keep their great relationship with us. You can trust sunnyda since there are 90% off rates who repeat their orders because of the excellence and durability of the Z beam steel we provide.
Sunnyda can be your superior partner and manufacturer of Z beam steel.
Z Beam Steel
Table of Contents
Introduction
Q1: What Is Z Beam Steel?
Q2: What Are The Applications Of Z Beam Steel?
Q3: What Are The Best Production Methods For Z Beam Steel?
Q4: What Are Z Beam Steel Types?
Q5: What Is The Difference Between Z Beam Steel And C?
Q6: What Are The Materials Used To Produce Z Beam Steel?
Q7: What Are The Advantages Of Using Z Beam Steel?
Q8: What Are The Dimensions Of Z Beam Steel?
Q9: What Are The Most Commonly Used Z Beam Steel Grades?
Q10: What Are The International Standards Of Z Beam Steel?
Q11: What Is The Maximum Load Can Z Beam Steel Support?
Q12: How Long Can Z Beam Steel Span?
Q13: What Is The Maximum Length Of Z Beam Steel?
Q14: What Are The Critical Factors To Consider Before Buying Lightweight Z Beam Steel?
Q15: Can Manufacturer Design Z Beam Steel?
Q16: Does Manufacturer Provide Z Beam Steel Customization?
Q17: Does Manufacturer Provide Plain And Punched Z Beam Steel?
Q18: What Anti-Corrosion Surface Protection Can Be Applied To Z Beam Steel?
Q19: Is Z beam Steel Can Be Galvanized?
Q20: What Surface Treatment Can Be Applied To Z Beam Steel?
Q21: Does the Manufacturer Provide Z Beam Steel Accessories?
Q22: How Much Cost Z Beam Steel In China?
Q23: Does Chinas Z Beam Steel Complies With International Building Codes?
Q24: Why Do Buyers Prefer Largely To Import Z Beam Steel From China?
Q25: How Long Does It Takes To Deliver Z Beam Steel From China?
Q26: How Much is The Average Shipping Cost From China?
Q27: How Sunnyda Can Offer Z Beam Steel Competitive Price, Quality & Service?
Q28: Does Manufacturer Keep Stock Of Z Beam Steel?
Q29: What Does Z Beam Steel Warranty Usually Cover? How Long Does It Last?
Q30: I have Additional Questions About Z Beam Steel?
Z beam steel
This frequently asked question guide briefly defines Z beam steel, applications, production process, while it provides a clear idea about various steel grades and galvanization types that can be applied to Z beam steel. It covers also other important topics about Z Beam Steel.
Z Beam Steel is horizontal structural steel sections that take the form of the letter Z, theyre used under several names Z section, Z axis, Z profile, Z purlin, Z-Bars, Z-Channels, Zees, roof profile, facade profile, light gauge steel construction profile, etc
Because of its overlapping capability, strength and loading capacity, Z Beam Steel acts as a support and reinforcements for structures by providing lateral stability to the primary frame members.
They are essentially designed to build the roof and wall joists of the majority of shell structures. They are mostly used for framing work, supports purlin, auxiliary element, facade profile, stiffeners, stringcourse, reinforcements, trims, edgings and structural components.
Z Beam Steels has become today a necessity in all residential, commercial and industrial steel structure construction to support mainly roof and wall sheeting and for many other purposes:
Steel building construction, Mezzanines flooring, roofing truss, wall sheeting, Load-bearing column and beam.
Heavy industrial steel structure buildings exposed to excessive loads.
Light gauge steel structure constructions, warehouses and hangars.
Auxiliary element in industrial construction.
Structural framing in medium-sized buildings, as well as barns, garages, patios and carports.
Floor framing, scaffolds, rails, etc.
Z beam steel
Automotive, car trailers, electricity and electronics.
Construction of oilfield support equipment, as industries platforms, petrochemical vertical steel structures etc
Garage Doors, Store Fixtures, Metal Furniture, Racks, etc
Roll Forming is a proven technology used to create Z Beam Steel; this reliable method allows producing large quantities of steel sheet and thus, creates constant-profile parts with specific lengths.
Roll forming can be produced either through:
Z Beam steel passes through a series of Cold-formed steel (CFS) processes or cold-working. The production is carried out through a set of rolling, pressing, stamping and bending operations. Cold-rolled steel (CRS) sheets are commonly used in all areas of steel manufacturing including.
This process allows the deformation of metals above their recrystallization temperature recrystallization is an important step as it keeps the materials strain to harden, this ultimately keeps the yield strength and hardness low and ductility high.
Hot metal can be worked using several methods such as rolling, forging, extrusion, and drawing.
Z beam steel
The rolling process of Z Beam steel involves a series of bending operations via one or multiple fabrication machine processes, which progressively shape a strip of long sheet metal or coiled steel through a consecutive set of rolls mounted stands till obtaining the desired Z profile.
Secondary processing includes stamping, punching, holes and cutting off any Z Beam steel length.
Z Beam steel is available in a diverse range of fully compatible Z profiles made from cold-rolled steel in depths ranging from 6 mm to 28 mm deep, indifferent standard or custom-made specifications, with or without returns flanges. The most common types of Z Beam steel are produced for Sleeved System, Double-span Sleeved, Butted, Heavy End Bay Systems, lapped and Single and Double Span Z beam steel.
Z Beam steel can form a well-proven structure system as well as a high degree of flexibility and strength, and weight-saving over hot rolled steel sections, along with simple handling during installation.
Z beam steel can be used over single spans, lapped continuous spans in multi-bay buildings as well as unlapped continuous. Whereas C sections can only be used over single spans and unlapped continuous spans. In addition to that, Z beam steel is stronger than C beam steel.
Z & C beams steel are used with each other as joints and overlaps.
Z Beam Steel can be made from high-tensile steel or mild steel. However, while high-tensile galvanized steel is mostly used, other metals such as stainless, aluminum, brass and copper remain also common. A variety of treatments and finishes using diverse coating and anti-corrosion protection materials are also applied to Z Beam steel.
Z beam steel
Z Beam Steel can be produced from light gauge low carbon mild steel of 2.30 mm to 4.50 mm thickness, conformant to JIS G & SSC 400.
Z Beam Steel is mostly made from Hot Dipped Galvanized High-Tensile Steel compliant with ASZ350. Thickness ranges from 1.50 mm to 3.00 mm, zinc coating Z275 (275g/m2) and minimum yield stress of 450MPa are applied.
Z350 (350 g/m2) zinc coating can be applied upon request.
G450 Steel: is a Z beam steel grade made from hot-dipped zinc-coated structural steel with a spangled surface, This steel grade guarantee a minimum yield strength of 450MPa. AS : and AS/NZS : are the main applicable standards.
G500 Steel: this is a hot-dipped zinc-coated structural steel used to produce Z beam steel; it offers a spangled surface and guaranteed minimum yield strength of 500MPa. Its Suitable for roll forming to a minimum internal diameter of 4t.
Its made according to AS : and AS/NZS : standards.
G550 Zinc: this grade of hot-dipped zinc alloy-coated structural steel offers a regular spangle surface while minimum yield strength of 550MPa is guaranteed.
12, 14, 16, 18 & 20 Gauge Galvanized Steel: a complete line of engineered Z Beam steel in different gauges can be provided; they are essential for framing work, supports, stiffeners, bracket and wall girt.
Z Beam Steel is considered an extremely economic and competitive solution due to its increased inertia, reduces deflection, large width and high-yield steel characteristics, which results in a good installation performance.
There are many advantages for constructing with Z Beam Steel:
Z beam steel
Production systems enable manufacturers to produce accurate Z beam steel to lengths of up to 9 m and up to a massive 500 mm deep x 6 mm. However, while Z beam steel can be customized according to customers required size and specifications. The following dimensions are commonly used:
Thickness: 1.5 mm to 3.2 mm.
Flange: 50 mm to 100 mm.
Lips: 15 mm to 30 mm.
Depth: 120 mm to 400 mm.
Weight: 2.80 Kg/m to 15.94 Kg/m.
The most commonly used Z Beam Steel Grades are summarized below:
This is a pre-hot dipped galvanized cold roll-formed steel which has a guaranteed minimum yield strength of 450N/ mm2 and can be galvanized using Z275 coating.
This is a plain carbon / mild steel structural steel that offers good cold bending performance, strength, toughness, plasticity, and weldability. It is classified under Chinese standard GB/T700. It is divided into four primary qualities: Q235A; Q235B; Q235C and Q235D and characterized by a Steel density of 7.85 g/cm3; a tensile strength of 370-500 MPa and a Yield strength of 235 MPa.
Z beam steel
This Chinese standardized GB/T is a low alloy medium tensile strength steel, it is made through a hot-rolling process. Q345 Z Beam steel has a material density of 7.85 g/cm3, it offers a tensile strength of 470-630 Mpa and yield strength of 345 MPa.
Q345 Z beam steel has better properties than Q235. It is classified under five quality grades (Q345A; Q345B; Q345C; Q345D and Q345E). Its known by its cold and hot workability, good weldability in addition to its corrosion resistance characteristics.
Q345 specifications are typical to ASME A572, it also covers the standard requirements for steel grades 42, 50, 55, 60, and 65.
China Z Beam Steel grades can be provided inclusion low carbon steel Q195; Q235A; Q235B; Q345B.
Z beam steel can be produced using European steel grades and standards of S235; S275, S355 and more.
Grade S350GD and S390GD + Zn 275 g/m2 are used to manufacture lightweight Z Beam steel / Z purlins compliant to EN , from cold-rolled thin gauge steel sheet, with a steel sheet yield strength of a minimum 350N/mm².
Commonly used Z Beam Steel meets the following Standards:
Z beam steel
Z beam steel is designed and produced in accordance to ASTM A570/A570M-98 Standards and Specification for Hot-Rolled Steel Sheet.
Cold-formed Z Beam Steel / Z Purlin / Z Sections are normally made from high-strength steel and galvanized as per A 653.7 ASTM Standard Specification, while its zinc-coated following G60 and G90 standards and ASTM A 525 which specify all kinds of metal coatings that can be applied by a hot-dip process.
ASTM A 312; A269; A511A can be produced along with JIS G; AISI, BS, DIN, GB standards, material grades, specifications, dimensions, etc
The North American Specification for the Design of Cold-Formed Steel Structural Members, determines the scope, specifications under which Z beam steel is designed.
This innovative version software optimizes the design of Z steel beam / Z purlins and side rails to meet North American Standards and the Middle East as well.
For the design of cold-formed thin gauge sections, code of practice for wind loads and imposed roof loads.
You will get efficient and thoughtful service from Yunsheng.
Structural design and rules for cold-formed members and sheeting.
Z beam steel
Z beam steel is preferred as load-bearing and auxiliary element to be used in light and heavy structural steel buildings construction to support the loads from the roof deck or sheathing.
A load factor of 1.5 is normally adopted for Z beam steel while general working loads are calculated in compliance with the following codes and standards:
British Standards Institution under BS EN -1-3 standards which determines the snow load to be used for structural design and snow loads on roofs which occur in calm or windy conditions; loads due to snow overhanging the cantilevered edge of a roof, loads imposed by snow sliding down, etc
ASCE/SEI 7-05 this is a clause of the United States building codes, it specifies clearly the wind and earthquake load provisions and provide minimum design loads and general structural design concerning wind, snow, rain, atmospheric ice, earthquake loads, dead, live, soil, flood and their combinations.
European standards for densities, self-weight, imposed loads: self-weight of construction works and imposed loads on buildings are designed as per BS EN -1-1 general actions.
European standards for wind actions: wind actions on structures BS EN -1-4: general actions are strictly applied in design, modeling of wind actions, wind velocity and velocity pressure.
Using Z Beam Steel can result in achieving a span of 15 m, this offers a flexible and column-free internal space, and reduce substructure costs and erection times.
Z beam steel used in the roof allows a maximum span of 12 m.
In single-span system Z beam steel can offer up of 6 10 m, this is mainly used in walls and roofs. Whereas, in double-span system 4 to 6m spans can be reached in walls and roof applications which necessitate moderate spans.
Z beam steel of a maximum length of mm Z beam can be produced, with a maximum of 4,00 mm to 400mm of web measurement and a maximum of 100 mm flange measurement.
Z beam steel
The following are the most important factors to consider before ordering Z Beam Steel:
Yes, absolutely.
Z Beam steel can be designed to suit each project requirements and specification using the latest technology software that optimizes effectively Z Beam steel design processes and can perform planning, creating detailed models for structural construction, visualizing projects, creating load tables, calculating Z Beam Steel requirements in a timely effective manner while minimizing costs.
Z Beam steel can be customized to suit customer precise requirements in design, materials, sizes, thicknesses, lengths, finishing, cutting and forming using computer numerical control (CNC) machines. All customization options can be provided including the following options:
Z beam steel
Thickness: 1.5 mm to 3.2 mm.
Flange: 50 mm to 100 mm.
Lips: 15 mm to 30 mm.
Depth: 120 mm to 400 mm.
Weight: 2.80 Kg/m to 15.94 Kg/m.
Up to 9 meters in one length;
Custom lengths also can be produced.
Custom sizes can be produced to meet original equipment manufacturer (OEM) requirements.
High accuracy press forming machines (BW Industries) are used to offer up to 9 meters in one length Z Beam Steel including even heavier gauges and longer lengths.
Z Beam steel can be cut to specified length requirements, using laser cutting to provide high-quality cutting of any shape while giving volume productivity at a minimum cost.
Standard and customized holes and slots can be punched and notched to the highest possible accuracy to suit any Z beam steel detail design requirements. Hole punching and notching process are made according to AISC guide.
A comprehensive range of tooling is used to produce Z beam steel punching and notching to almost any size, any steel gauge, any shape holes, in any number, to any position.
Computer-controlled punching stations and CNC Turrett Punch Press with 30 tons high-speed servo hydraulic punching head, which allows the punching of flat sheets of x mm and cold-formed sections up to 6 mm thick Z beam steel.
Hole of 22 mm diameter: suitable for M16 bolts and for big size Z beam steel webs of 300 mm and 350 mm.
Hole of 18 mm 22 mm diameter: suitable for M12 bolts and for 100; 150; 200 and 250 mm deep Z Beam steel.
Special projects: Z beam steel hole numbers, sizes and gauge lines can be modified to suit required design performance.
Z Beam steel can be supplied un-drilled or with pre-drilled holes at any hole diameter size including small size holes, using high-speed steel (HSS) drills, Core drills/Hole saws, etc
Z beam steel
Yes, Z Beam steel can be supplied blank or punched according to customer specifications.
Punching and blanking are metal fabrication processes that involve cutting the Z Beam steel surface into specific forms. This process enables highly specialized parts to be produced in addition to minimizing waste and cost.
In punching, a scrap slug is removed as the punch enters the punching die, leaving a hole in the Z Beam steel workpiece. On the other hand, Z beam steel Blanking creates a geometric shape or blank from the primary material, by feeding the steel sheet into a press and die.
Z Beam steel is typically prefinished with galvanization or other rust-inhibiting coating materials such as:
Hot-dip galvanizing offers excellent anti-corrosion protection in the most demanding corrosive atmospheres. Z350 (350g/m2) galvanizing coating is recommended for Z beam steel used in a non-aggressive environment; it offers excellent protection, long life lasting and maintenance-free. While, Z450 (450g/m2) galvanizing coating is preferred for severe corrosive atmospheric conditions such as marine and industrial environments. The heavier galvanizing coating also can be provided based on customers requests.
Zinc coatings with different coating thicknesses, surface qualities and surface treatments can be applied to Z Beam steel to meet the demands of various applications.
Zinc coating provides excellent adhesiveness, uniformity, ductility and good frictional behavior while the zinc lubricating effect makes it easy to mold and offers a graceful finished surface to Z beam steel.
This anti-corrosion coating type can meet aesthetic visual appearance requirements due to its crystallized zinc spangle. It can last up to 80 years and can be reached using zinc coating range from Z100 to Z600 (42 µm on both sides) with a composition of zinc coating which consists of (>99%) zinc.
Z beam steel Zinc coating thicknesses are defined in accordance with EN: technical requirements.
Zinc coatings are available in a wide range of qualities and surface treatments. It can be made to meet different coating thicknesses specifications and meet the demands of various applications. Upon request, OEM Z beam steel zinc coating can be also fulfilled.
Z beam steel
Galvanized Z Steel beam is preferred due to its excellent corrosion resistance, long life lasting and sustainability. Those factors made it highly effective and suitable for rust prevention, for exterior and interior applications; the following galvanized steel types are the most used in Z beam steel application:
Z beam steel can be pre-hot dipped galvanized with Z275 (275g/m2) Zinc coating. This type of zinc coating can offer minimum yield strength of 450N/mm², with a minimum spangle suitable for both painted and unpainted Z Beam steel applications. Z275 is available in different thicknesses from 1.50 mm to 5.00 mm.
This coating class is applied to Z beam steel in conformance with AS standards which define zinc coating class, hot-dip metallic coated sheet steel and weights to be strictly followed in Z Beam steel coating.
However, while Z275 is the normal coating class for Z beam steel, the following remains optional:
This is an aluminum-zinc alloy (Galvalume) that offers a fine spangle suitable for Z beam steel painting without any other treatment.
Z350 (350 g/m2) and Z200 are reliable and efficient galvanization solutions that can suit effectively all Z beam steel aesthetic and performance requirements.
Z450 and Z600 are hot-dipped galvanized heavy-coating known for its long life-time and excellent surface aspect which blends in almost all storage environments. Its widely used for Z beam steel being competitive in terms of price and quality.
Z Beam steel can be zinc-coated (galvanized) in accordance with ASTM A653 and ASTM A Standard Specification.
G40 galvanization: is applied to Z beam steel made from 25 and 20 steel gauges and coated with ASTM A.
G60 galvanization: this galvanization type is applicable mainly to Z beam steel produced from 18 gauge steel and greater and coated in accordance with ASTM A guide.
G90 Galvanized: Z beam steel is hot dipped in zinc and coated with a minimum 0.90 oz. of zinc per square foot. This process provides 50 percent more zinc protection to Z beam steel. This type of galvanization offers excellent corrosion resistance and suits more all Z beam steel exterior applications.
Z beam steel
A variety of cost-effective and resistant surface treatment can be used to enhance the aesthetic of Z beam steel and ensure abrasion and anti-corrosion protection including:
Z Steel Beam manufacturer can provide a variety of compatible accessories that can be supplied for all structural design and cladding types including:
Z beam steel
Hot-rolled galvanized Z Beam Steel costs approximately: $450 per Ton.
Z beam steel prices may vary according to quantities and customization level required.
To enquire about Z Beam Steels best prices please contact today.
Yes, effectively. Chinas Z beam steel is produced in compliance with International Building Codes (IBC) and countries local building codes. Chinas Z beam steel producers apply strictly all regulations that govern Z beam steel performance, design, technical specifications, materials, load requirements, seismic forces resistance, fire safety code, etc
A key reason that builders and business owners from all over the world choose to import Z Beam steel from China is that Z Beam steel Chinese manufacturers have all the resources, capabilities, technology and production capacity to produce all ranges of Z beam steel in large quantities. This reduces manufacturing costs and significantly lowers the price of Z beam steel and increases the profit margins for importers.
Furthermore, Chinese Z Beam steel producers can offer a one-stop-shop solution including design, manufacturing, customization and all related services at a cost-effective while quality and on-time delivery are ensured. This saves customers time, money and provides access to the most innovative Z Beam steel.
Chinese Z Beam steel has gained global steel industry popularity; construction sector investors rely heavily on China Z beam steel imports to build high-quality, sustainable buildings at an affordable cost.
Z beam steel production can be processed in 2-5 days according to order quantities and customization requirements, while shipping by Sea freight takes around 10 to 25 days.
Z beam steel
Z beam steel shipping cost from china depends largely on weight and destination.
To ship one 20 containers from China to South Africa, during peak seasons is estimated at the rate of - $ around
Please note that almost all Z beam steel is made from Light Weight Steel, so this may result in less shipping cost.
For more accurate information about Z beam steel shipping cost, please contact:
Sunnyda is a name you can trust; its a synonym for effectiveness and Efficiency in designing, producing and exporting high-quality and affordable Z beam steel for various applications.
Sunnyda is one of the best Chinese producers of cold-rolled sections including Z beam steel, with a production capacity of more than 1,000,000 tons per year and a production system that enable manufacturing Z beam steel in a high degree of strength and accuracy. There are virtually no limitations in design, size, length, customization requirements and technical support when you need it.
Our Z steel beam can be produced for sleeved, double-span sleeved, butted and over-lapped systems.
Sunnyda Z Beam Steel is certified by the leading international standardization organizations:
Z beam steel
Yes, Z Beam steel standard sizes are available on stock, while special sizes and customized Z Beam steel are made to order. Contact us now or visit our store for more details. We are located at: No 29, Huahui Road, Songjiang District, Shanghai, China.
Z beam steel manufacturers offer comprehensive warranties that cover not only the steel materials, coating and corrosion performance but also the serviceability performance.
The manufacturer can back their Z Beam steel with 20 years.
Z beam steel coating treatments warranty is subject to inquiry, please contact:
Z beam steel material deemed to be defective will be replaced at no charge by Sunnyda upon showing evidence.
If you have any questions about Z beam steel, if you require more details about our best prices and services, if you need more advice about your current project steel, please contact us now today
Are you interested in learning more about Z-Beam? Contact us today to secure an expert consultation!