The company is the world’s best Wire Greenhouse Bench supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.
Greenhouse Benches
By Nick Ostrovsky
Greenhouse Benches
Choosing a greenhouse bench design, material and layout can be a formidable task considering the scope of options a grower has. It is very important to decide what the primary objectives of your greenhouse are before you either purchase or design and build a bench system. You must consider what type of plant material you will be dealing with primarily. Will you be sowing seeds on large flats or will you be planting into 5 gallon containers? Will you require bottom heat or misting units? Will you be able to grow directly on the floor or do you need a raised platform for working? What bench conformation will be the most efficient in your green house? How much room will you require to maneuver around your benches? Can your benches be fixed into place or will you need to move them around? How large of a budget do you have? This chapter will address these questions that you must consider when thinking about your greenhouse.
Choosing a bench type
The cheapest way to grow plants is on the ground. However, on the ground, accurate temperature control is difficult to achieve, and other problems may complicate growing, including, disease and rot. Benches, therefore, are recommended. There are a variety of bench styles available. When choosing a greenhouse bench design, you must account for many factors; weight capacity, durability, rot resistance, cost, ease of movement, weight, air flow, water flow, appearance, height and inertness etc.
Materials
Regardless of the building materials chosen, benches normally do not exceed 36
inches high or wide when against a wall. Freestanding benches which are not
against the wall may be up to six feet wide to allow work from either side.
Freestanding benches should also not exceed 36 inches high to accommodate
regular work. (1)
Allow air circulation for plants by having an open bench floor. This may be accomplished by a number of materials such as redwood, lath, 14 gauge welded wire fabric, or expanded metal. Be certain enough rigidity is offered to prevent sagging and toppling pots. Regardless of materials chosen for bench construction, a good rule of thumb is to allow support for at least 25 pounds per square foot area. (1)
Wooden Benches
Locust, cedar, redwood and cypress are all woods highly resistant to decay. You
should paint wooden benches with copper naphthenate
or other preservatives (known to be safe around plants) to help decay. When
redwood is chosen, iron and steel will corrode from naturally present decay
inhibitors. Therefore, choose metals such as aluminum, zinc or brass nails,
screws and bolts. Benches may be all wood or in combination with a different
material for the base. Often, expanded metal or welded wire, of one inch or
smaller mesh, are used. While expanded metal is more expensive, it does not sag
like welded wire. Besides decay, wood may warp and often absorbs soils,
chemicals, etc. which cannot be adequately removed. When wood is chosen, higher
maintenance will be required on a regular basis. (1)
Concrete
Some greenhouses have entire concrete poured benches, including the legs
(supports), all at once. These benches are permanent and do not allow for
change later. Concrete benches are durable and will not require additional
treatment to prevent decay such as with wood. They may be reinforced with steel
rods, when poured, for additional durability. You may want to consider drilling
holes in the base of the bench for proper drainage. (1)
Metal
Entire metal or steel benches are used alone or in combination with another
material. Advantages of galvanized metals over wood are the longevity and
resistance to rot and decay. Metal benches may be expensive to install
initially, but can be considered a one-time cost. Also consider the lowered maintenance
costs when these types of benches are used. (1)
Plastic
Although plastics are becoming more common for bench beds, plastic frames are
not always desirable. They are often not as durable or able to support as much
weight as other benching materials. Prefabricated plastic benches can be
purchased which are lightweight and, thus, portable. These are also available
mounted on rollers, making them particularly convenient for moving around. Also,
maintenance on plastic benches is again considerably less than for wood. (1)
Pallets
Another portable bench system can be inexpensively constructed by placing
pallets on cement blocks for support.
(1)
Bench Supports
Cement blocks are commonly used to support bench tops, particularly if they are
not intended to be permanent. Permanent benches may also be supported in this
fashion. Additionally, steel poles can be used for bench support. Plastic bench
supports can also be used, but again, they are often not as strong. When wooden
supports are used, it is especially critical to chemically treat them for
decay, at least the area which will be submerged in the soil. The same
preservatives which may be used on the growing surface of the benches are
appropriate. Also, by pouring concrete footings, the structural integrity of
the bench supports may be reinforced. (1)
Where to buy a bench
You can buy benches at a number of greenhouse retailers (both commercial and retail), See list below. You can also purchase (or acquire for free) bench building plans. See list below. It is important to note however that some plans require a significant amount of carpentry skill.
(1)
American Plant Products and Services, Inc.
9200 N.W. 10th
Street
Oklahoma City, OK. 73127
(405) 787-4833
AQUA-HORT SYSTEMS, INC.
P.O. Box 57197
Oklahoma City, OK. 73157
(405) 521-8002 US: 800-446-1694
Growers Intl. Inc./Div. of
Sharp & Son, Inc.
P.O. Box 10
Schulenburg, TX 78956
(409) 743-6522
Growing Systems, (M, W)
2950 N. Weil
Milwaukee, WI. 53212
(414) 263-3131
Metalex, Inc., (M)
1530 Artiaus Pkwy
Libertyville, IL. 60048
(312) 362-8300 US: 800-323-0792
Nexus Greenhouse Systems Corp., (M)
10983 Leroy Dr.
Northglenn, CO. 80233
(303) 457-9199 US: 800-2-BUY-NEX Fax: (303) 457-2801
Rough Brothers
P.O. Box 16010
Cincinnati, OH. 45216
(513) 242-0310 OH: 800-543-7602 US: 800-543-7351 Fax: (513) 242-0816
Sharp & Son, Inc.
900 Lind Ave. SW
Renton, WA 98055
(206) 235-4510
Westbrook Greenhouse Systems, Ltd. (M)
P.O. Box 99
Grimsby, ON Canada L3M 4G1
(416) 945-4111 US: 800-263-0230 Fax: (416) 945-6564
Structural Plastics Corp.
2750 Lippincott Blvd.
Flint, MI 48507
(313) 743-2800 US: 800-523-6899 Fax: (313) 743-2799
Dramex Intl., (M)
20 Fasken Dr.
Rexdale, ON Canada M9W 1K5
(416) 675-6311 Fax: (416) 675-4310
B & C Mortensen Wood Products
Rt. 4, Box 1000
Oldtown, ID 83822
(208) 437-5665
Barlow Tyrie, Inc., (M)
1263/230 Glen
Ave.
Moorestown, NJ 08057
(609) 273-7878 US: 800-451-7467
Southeastern Wood Products Co.
P.O. Box 113
Griffin, GA 30224
(404) 227-7486
Websites
Agra-Tech Systems: http://www.agra-tech.com
BartlettBench and Wire: http://www.quikpage.com/b/bartben
JancoGreenhouses: http://www.jancoinc.com
Keeler-Glasgow: http://www.keeler-glasgow.com
Nexus Corp.: http://www.nexuscorp.com
Rough Brothers Inc.: http://www.roughbros.com
Stuppy Greenhouse Manufacturing: http://www.stuppy.com
X.S. Smith Inc.: http://www.xssmith.com
Bench Plans
Figure 1 Basic wooden bench plan.
Free plans: http://www.freeplants.com/free-potting-bench-plans.htm, http://www.hobby-greenhouse.com/BENCH2.JPG
Bench layouts
The internal bench layout of greenhouses depends upon many factors. Benching systems vary but usually are of the fixed or 'movable type. The fixed longitudinal bench is the most traditional system and by its very nature demands the most labor for handling the crop. With long narrow aisles a worker has to travel long distances before they can exit the aisle. (2) (1)
Peninsula benches provide for a wide center aisle and fixed benches with short narrow aisles between them, perpendicular to the sides of the greenhouse. With this system it is possible to use transport carts in the wide center aisle, the distance for a worker from any point in the greenhouse to the center aisle is short. The wide center aisle also provides for the passing of plant material and pots easily. (2) (1)
Lastly, non-stationery benches, which provide even more growing space, are gaining popularity with growers. Movable benches, known as rolling benches, can increase efficiency up to 90 percent of the floor space. Bench platforms are moved by a crank at the end of the bench from side to side. Some can be moved by hand by sliding the benches over the top of long steel poles. Aisles are created where the grower wants to work at any given time. Rolling benches are easy to move by practically any laborer, which is an added bonus. Movable benches, however, are not appropriate in a setting where plants must be accessed frequently. (2) (1)
Figure 2 shows the different types of greenhouse bench layouts.
Peninsula
Longitudinal
Moving
Figure 2. Greenhouse bench layouts.
Bench Space Efficiency
Benching efficiency is defined as the square feet of bench space to the entire
greenhouse floor area. This number is expressed as a percentage.
If you want to learn more, please visit our website wire mesh security fencing.
Examples: A grower chooses a longitudinal bench arrangement in a greenhouse 30' x 80' or 2400 square feet of floor area. He decides to use 3-foot wide benches and 2.5-foot wide aisles and allows four feet at the end of the benches. The greenhouse has a benching efficiency of [5(number of benches) x 72(length of each bench) x 3(width of bench)]\ (30 x 80 greenhouse dimensions) x 100 = (1080/2400) x 100 = 45%.
However, if the benches were widened to four feet and 74 feet long, allowing a three-foot turn around rather than four feet as before, efficiency could be increased to 49 percent [(4 x 74 x 4)/(30 x 80) x 100 = 49%]. To further increase efficiency, the benches could be widened and the aisle widths reduced. Table 1 shows the space utilization for various benching schemes. (2)
Table 1 Space Utilization for Various Benching Schemes
Longitudinal Benches
67%
Peninsula Benches
74%
Movable Longitudinal Benches
82%
Movable Peninsula Benches
86%
Transportable Benches
93%
Floor System
90-92%
References
1. Michael A. Schnelle, Greenhouse Floors and Benches. Oklahoma Cooperative Extension Service, OSU Extension Facts. Found at:
http://pearl.agcomm.okstate.edu/hort/greenhouses/f6703.htm
2. US Global Recourses,
Technical Library: Benches.
Found at:
http://www.technical-library.usgr.com/tl_benches1.html
3. Hobby Greenhouses. Found at:
http://www.hobby-greenhouse.com/BENCH2.JPG
Section 1: Greenhouse Benching and Production Surfaces
The choice of a greenhouse benching system, or better stated as "production surface", is affected by many variables. In the past, the choice of production surfaces was dictated primarily by labor concerns (i.e. bending and reaching), cost, and ease of movement around the structure. These factors are still important, but with changes in production technologies (particularly irrigation and fertilization methods), additional considerations have become important when determining what type of production surface to install in a greenhouse. Production surfaces in greenhouses may be raised or elevated benching systems or they may be located on the greenhouse floor. When deciding upon a production surface for greenhouse crops production, the following are some important aspects to consider:
Production surface height
The height of the production surface is important primarily because of how it impacts people who must handle the plant material. If it is too low, workers must bend to work with plant materials, and this can result in worker fatigue and even potential health problems. If the benching surface is too high, it may be difficult for workers to reach and work with plant materials. If a raised production surface is used, a height of 3-3½ feet is typically utilized. Where floor-based (i.e. gravel floors, flood floors) production systems are used, height is irrelevant (since it is on the ground) although workers must still bend to work with plant materials. In some cases, crops may be elevated higher than 3-3½ feet above the floor. Hanging baskets may be hung above head height to increase space usage. Gutters used for greenhouse strawberries may be shoulder height to facilitate picking of fruit and plant maintenance.
Production surface width
The desired width of a raised production surface is dictated primarily by two factors. The first is that workers must be able to reach plant materials. If workers have access to both sides of a raised bench, 5 feet widths are recommended. If workers can only access the raised bench from one side, the width should not exceed 2.5 feet. If plant materials are grown on some type of floor, spacing of aisles will depend upon whether plant materials will need to be accessed between the time they are placed on the floor and when they are removed and shipped. If plant materials must be pinched or handled during production, aisles must be placed in such a way as to allow access to the plant materials by the workers. If plants are automatically irrigated and will not be handled until shipping, worker access is not as important and aisles may be eliminated or spaced far apart.
Production surfaces must also be adapted to automation that is in use. For example, if boom irrigation systems are used, the width of the boom arms will dictate the width of the raised benches or the spacing of the aisles on floor-based production surfaces. If ebb-and-flow benches are used, the width of the bench will be dictated by the irrigation trays that are available.
Air and drainage spaces in production surfaces
Openings in the surfaces of raised benches allow water to drain off the surface of the bench and for improved air circulation. If water collects on the bench surface, and especially if the surface is not level, the substrate of some portions of the crop will tend to remain wet while other areas dry out and require irrigation more often. This uneven drying can result in differences in water availability as well as differences in mineral nutrition if a liquid fertilization program is being used. This in turn can result in the development of a non-uniform crop. Additionally, "wet spots" on a bench can result in increased disease incidence.
Ebb-and-flow benches are raised benches with plastic flood trays that do not have openings in the production surface (otherwise the benches could not be flooded). However, ebb-and-flow flood trays have two levels of channels that allow for drainage away from the container as well as for improving air circulation.
If floor-based production surfaces are used, they are often covered with small gravel that allows for water drainage. If concrete floors are used, they may be grooved or laid with a small grade to promote drainage of water off of the production surface.
Strength
Raised benches must support the load of plants, containers, and wet soil. These loads can be high, particularly when close spacing of plant materials is used. Both the bench surface and its underlying support structure must be able to hold up to the required loads.
Floor-based production surfaces must support the weight of the crops, preferably without settling and creating indentations that retain water and cause “wet spots”. Floor-based production surfaces may also need to support the weight of equipment that may be placed upon them or vehicles that may be driven across them.
Cost
There are two primary costs associated with production surfaces. The first is the cost to purchase, assemble and maintain the production surface. Obviously, the lower the cost, the more attractive is the surface. However, the true cost must also include the lifespan and whether any production cost savings are achieved by using a particular production surface. If a production surface must be replaced often, its initial low cost might not be as attractive as a more expensive one that will last for a much longer period of time. Additionally expensive production surfaces, such as ebb-and-flow benches and flood floors, may be expensive in and of themselves, but they may allow a producer to reduce labor, irrigation and fertilizer costs and may in the long-run prove to be economical.
Another important cost aspect of production surfaces is that of space usage efficiency. A 100,000 ft2 greenhouse will not necessarily have 100,000 ft2 of potential revenue generating area since plants are typically not grown in aisles or other auxiliary areas. The objective is to maximize the area under cover that can be used to actually grow plants and generate revenue. This area is expressed as a percentage of the total area under cover and is referred to as the space usage efficiency. Maximizing space usage efficiency can be very important in keeping production costs down and maximizing profits. All fixed costs (i.e. payments on the greenhouse structure) and many variable costs (i.e. heating the structure) of production must be allocated to the crops grown in the structure. This is typically done by assigning a certain cost per ft2 of production area per week or per day. Any crop using that space is assigned that cost. The greater the actual area that can be used to grow plants, the lower the dollar value that must be assigned per ft2 per day or week. At the end of this learning unit, you will learn how to calculate space usage efficiency and see specific examples of how increasing space usage efficiency can reduce costs.
Compatibility with irrigation methods
Numerous systems have been developed that combine the production surface with an irrigation system to reduce labor costs associated with irrigating and fertilizing plants, to prevent run-off and to save water and fertilizer. Some of these combined production surface-irrigation systems include ebb-and-flow benches and flood floors. In other situations such as with irrigation booms, the bench or production surface must be designed to be compatible (i.e. same width) with the irrigation system. When selecting or designing a production surface, compatibility with irrigation systems (both in the present and in the future) should be considered.
Support requirement
The type of support system required (structure underneath the surface of a raised bench) for a production surface will partially depend upon the load the bench must support. However, different types of production surface materials also require different types of structural supports. Expanded metal is very strong and rigid. Therefore, it requires little support underneath. However, wire mesh is flexible and bends easily. This type of surface material will require many more supports underneath the surface to provide and maintain a level production surface. Rolling benches and Dutch tray systems require a more elaborate support system than stationary benches since they must be easily moved even when bearing heavy loads.
Floor-based benching systems (i.e. flood floors) must be strong enough not only to support plants and people, but also any equipment that may be placed on or driven across the floors.
Adaptability to new technology
As technology changes, production surfaces may need to change. If the production surface in use cannot be adapted to the new technology, it will either have to be replaced or the new technology not utilized in the operation. Production surface systems that allow maximum flexibility will best allow for the use of new technologies.
Section 2: Greenhouse Benching Materials
The support structure of elevated benching systems may be made of concrete blocks, wood, or plastic. However, galvanized steel or aluminum are most commonly used to make the structural support of elevated benches.
The surface of elevated benches may be made of expanded metal, wire, wood, hardened plastic, chain-link fence, snow fencing, or concrete. Each of these materials has advantages and disadvantages. Hardened plastic is resistant to water and chemicals and can support heavy loads, but hardened plastic benches are expensive and typically only used in special situations such as propagation houses and retail displays. Another use for plastics in greenhouse benching is in the production of the bench liners used in ebb-and-flow benching systems. Wood is readily available and can be lower in cost than other materials (or more expensive than some materials). However, wood must be treated to prevent decay and can be difficult to clean. Wire and chain-link fence are low in cost, but because they bend easily, they require a significant support structure underneath to prevent bending and warping and to maintain a level production surface. The most common benching material is expanded metal. It is preferred because it is relatively low in cost, strong, rigid, and requires minimal support underneath. Expanded metal is also low maintenance and has a long lifespan.
Floor-based production surfaces may be made from standard or porous concrete. Floor-based production surface may also be constructed of compressed soil covered with a thick polypropylene mat that covers the ground but allows drainage. Floor-based production surfaces may also be covered with small gravel.
Section 3: Common Greenhouse Benching Systems
There are many types of benching systems or production surfaces used in greenhouses. Some are elevated while others utilize the floor of the greenhouse. Some serve only to support the plant material while others are hybrid systems that also allow for irrigation of the crop and even transport of the crop around the greenhouse facility. Listed below are common benching and production surface systems. In some cases, the system is described as a general category while others are distinct types of benching systems or production surfaces.
Stationary elevated benches
This term refers to a general category of bench types rather than a specific benching system. This is because stationary elevated benches may take many forms, but, as the name implies, they cannot be (and are not designed to be) easily moved. Stationary elevated benches may be supported my numerous materials including concrete blocks, wood, steel, aluminum or even hardened plastic. In some cases the support structure may simply rest on the greenhouse floor whereas in other cases it may be mounted in or bolted to the floor. The surface of the bench may be made of wood, wire, wire cages, expanded metal, snow fencing, chain link fence, ebb-and-flow irrigation trays, irrigation troughs or other types of materials. Stationary benching systems generally have the lowest space usage efficiency and offer the least flexibility.
Rolling elevated benches
Rolling benches is a term that also refers to a general category of bench types because there are numerous rolling bench designs. The surfaces of these benches are mounted onto the support structure in such a way as to allow the surface to be moved or "rolled" from side to side or even from location to location throughout the greenhouse facility. Rolling benches allow for a reduction in the number of walkways required and thus an increase in the space usage efficiency. Some types of rolling benches (i.e. Dutch trays) also provide a transportation system within the greenhouse structure. However, the use of rolling benches reduces access to plant material. As with stationary benches, rolling benches come in many forms and may be constructed of different materials. Specific examples of rolling benches are discussed below.
Removable benches
Removable benches are generally stationary but are designed to be repositioned or removed from the greenhouse during certain times of the cropping season. For example, a greenhouse manager might want to have a raised bench when growing a poinsettia crop (to improve drainage and air circulation) but might want to grow the following crop of bedding plants on the floor to maximize space usage efficiency. Removable or temporary benches could be assembled in the greenhouse for the poinsettia crop and then removed for the bedding plant crop.
Many types of removable benching systems exist. These are simple and temporary benching systems that are not mounted to the greenhouse floor. The support structure is typical made of concrete block, aluminum, steel or wood. The surface may be wire, wire fencing, wire cages, snow fencing or other low cost and easily movable materials.
Wire cage benches
There are several designs of wire “cage” benches. These benches may be simple wire or more complex systems. However, they are all designed for containers to be placed into the openings of the wire. The wire then holds the containers in place. These tend to be relatively low cost and simple raised benching systems. However, the dimensions of the openings in the wire must match the container size being used. These benches may be set to be permanent or removable and are most commonly used in growing tall or top-heavy potted plants since the cage holds the containers in place and prevents plants from falling over.
Ebb-and-flow benches
Ebb-and-flow benches (also called ebb-and-flood benches) combine an elevated benching system with a closed recirculating irrigation system. Ebb-and-flow benches may be designed as stationary benches or as rolling benches.
The primary characteristic of an ebb-and-flow bench is the tray that makes up the bench surface. The tray may be made of hardened plastic or aluminum. The length and width of the tray varies depending upon the desired bench dimensions. The tray has side walls that are generally 4 to 6 inches tall. On the bottom inside of the tray, there are two layers of channels with one being about ½ inch deep and running the length of the tray and the next set being about ¼ inch deep and running perpendicular to the length of the tray.
At one end of the tray there is an inlet and an outlet. The inlet allows fertilizer solution (or water) to be pumped into the tray. As fertilizer solution is pumped into the tray, it first floods the deepest of the channels. When the deepest channels are flooded, the solution floods the next level of channels. After both sets of channels are flooded, the solution continues to rise above the bottom surface of the bench. In a production situation, containers with plants would be placed on the tray surface. As the solution floods the tray and rises up around the bottom of the containers, the solution would come into contact with the root substrate inside of the containers and the fertilizer solution would move up and into the substrate in the container by capillary action. Thus, rather than top watering, the crop is subirrigated (water and/or fertilized from the bottom). When flooding, the depth of the solution is maintained so that it does not extend more than approximately ¼ to ½ of an inch up the height of the container (the container is sitting in a fertilizer solution that is ¼ to ½ inch deep). For a 4 or 4.5-inch containers (or smaller) the flooding depth is typically about ¼ inch while it may be ½ inch for larger containers. The fertilizer solution is allowed to maintain contact with the containers (and the root substrate inside) for approximately 10 minutes and then drained through the tray outlet.
The depth of the solution and the exposure time are controlled through several possible methods. In the first, the fertilizer solution is pumped into the bench through one of two pipes. At the same time, fertilizer solution flows out of the tray through an opening with a metal screen. The screen, however, allows the fertilizer solution to flow out at a slower rate than it flows in and the net effect is that the bench floods. The depth of the flooding is dictated by how fast and how long the fertilizer solution flows into the bench (inflow rate and screen size may be adjusted to change the flooding rate and level in the tray). A more well controlled method is one in which the fertilizer solution is pumped into the tray. The tray has an elevated outlet so that solution flows out only when it reaches a certain depth (or height). This prevents the solution from rising above a certain height. The inflow of solution can continue for as long as flooding is desired. When the desired flooding time is reached, the pump is turned off and the solution can flow back to the holding tank through the same plumbing that the solution was pumped into the flood tray. Other systems may have the outlet on a timer. The bench is flooded and after a prescribed period of time, the outlet is electronically opened so the fertilizer solution can flow back to the storage tanks.
All ebb-and-flow benches have several critical support components. There must be large storage tanks that hold the water or fertilizer solution used to flood the benches. The storage tank must have at least enough capacity to fill the benches being flooded at a given time. The size of the zone being flooded can be reduced to allow for smaller storage tanks. Additional storage tanks that contain concentrated fertilizer solution and plain water may be included. The system requires a pump to force the fertilizer solution from the storage tanks to the benches. Typically, some type of filter (i.e. sand or screen) is placed between the bench and the storage tank in the return flow line so that soil or plant debris is screened out. Timers or computer controls may be used to automate the irrigation process.
Probes may be placed in the line flowing from the storage tank to the trays to monitor electrical conductivity (E.C.) and pH. If the E.C. is too low (due to plants removing fertilizer elements from the solution for example), concentrated fertilizer stock solution may be added to the fertilizer solution to increase the E.C. to the desired level. If the E.C. is too high, plain water may be added to lower the E.C. If the pH is not within an acceptable range, an acid such as phosphoric acid, sulfuric or nitric acid may be added to decrease the pH or a base such as potassium hydroxide may be added to increase the pH.
There is a risk of spreading soil-borne disease-causing organisms such as Pythium and Phytophthora species in recirculated fertilization solutions. Therefore, after the solution is drained from the bench and filtered, it may be treated with U.V. light or ozone to kill any organisms present. Additionally, chloride, fluoride or copper may be added to the fertilizer solution to kill any disease-causing organisms present. More detailed information regarding disinfestation of water and fertilizer solutions is presented under the “Irrigation” learning unit. Ebb-and-Flow benches provide an efficient and automated irrigation and fertilization system. In addition to preventing runoff of water and fertilizers, ebb-and-flow benches reduce water and fertilizer usage. Therefore, although they are initially more expensive than many other types of benches, water, fertilizer and labor savings may make up for this initial cost over time.
Dutch trays
Dutch trays are very similar to ebb-and-flow benches. However, the flood trays are usually aluminum. Additionally, where ebb-and-flow systems may be designed as rolling benches, they are usually limited to simply rolling from side-to-side to minimize the number of aisles required and thus increase space usage efficiency. Dutch trays are placed on steel tracks that serve to not only support the trays, but the trays (which have small wheel-like structures underneath) roll on the metal support structure. This allows trays to be rolled together to maximize space usage efficiency, but the track system also serves as a transportation system around the greenhouse facility.
The tray units for a Dutch tray system may be rolled down the length of the greenhouse and spaced tray to tray. When the plant material needs to be moved to another location in the facility, the trays may be rolled on the steel tracks to a major aisle or walkway. When a change in direction is needed, the tray may be offloaded from tracks going in one direction and onto tracks going in a perpendicular direction using pneumatic lifts that raise and lower sections of track.
Because of their degree of mobility, Dutch trays cannot be physically connected to the fertilizer solution supply line or the drain line (otherwise all the tubes and supply and drainage lines would have to move with the trays). This problem is solved by having stand-alone supply lines and a drain line that runs underneath the benches but does not connect directly to the trays.
Although a Dutch tray system provides an automated transportation system, a closed recirculating irrigation system and maximizes space usage efficiency, it does limit access to crop. For example, if crops that need to shipped or handled are in the middle of a greenhouse, many trays might need to be moved to gain access to the trays with the desired plants. One solution to this problem has been to utilize various types of crane systems that can move over top of the trays, reach down, pick up a desired tray and bring the tray to the end of the greenhouse and place it on an open track.
Troughs
Troughs are narrow linear benching structures typically made from aluminum, plastic or PVC. There are several distinct types of troughs but they all are generally designed to hold a single row of containers or plants. Troughs may be open faced and designed to have containers placed on them or they may be a closed faced (or partially closed faced) and designed to have plants placed directly into the trough without a container. In all cases, the trough is mounted on some type of support structure with a slight grade (2% to 3%) from one end to the other to facilitate the flow of water or fertilizer solution.
One type of trough system is designed to support plants in containers. In this case, the trough is open faced and often has a shallow channel in the trough where the container is placed. The trough is positioned on a slight grade to facilitate the flow of the water or fertilizer solution. At the high end of the trough, a supply tube discharges water or fertilizer solution into the trough. The solution flows down the length of the trough in a shallow stream. As the solution comes into contact with the containers, and thus the substrate inside of the containers, solution is taken up into the substrate through capillary action. Excess solution is recaptured at the opposite end in a collection tray or manifold. The excess solution is typically filtered and returned to storage tanks. The recollected solution may be disinfested and monitored in the same manner as described for ebb-and-flow trays.
Another type of trough system is commonly used for the hydroponic production of greenhouse-grown vegetables and herbs. These are typically closed-faced troughs or partially closed-faced troughs made from plastic or food-grade PVC. The trough is designed so that seedlings or young plants may be pushed or slid into the top of the trough. The seedlings may have been germinated in Oasis® foam, an Ellipot® or in some other type of substrate. The root ball and substrate are held in place by the trough and thus the trough provides physical support to the plant. The shoots of the plants grow above the trough while the roots grow inside of the trough. As with the previous type of trough system, a stream of water or fertilizer solution flows inside the trough from one end to the opposite end. The flowing solution is typically a thin film or layer of solution that baths the roots as it flows down the length of the trough. In this way, the plants have access to water and mineral nutrients, but are not totally submerged in water. This method of supplying water and nutrients is sometimes referred to as the nutrient film technique (NFT). The trough used in this type of system may have varying designs and dimensions, may be supported on some type of elevated benching structure or may be close to the ground. This system is discussed in more detail in the "hydroponic systems" learning unit.
Another type of trough system is typically used for propagation. This system uses PVC pipes with a notch removed (partially open faced) along the length of the top of the pipe. Oasis® foam or trays with some type of substrate may be slid into the trough. Vegetative cuttings are stuck into the foam or substrate. The cuttings are misted using an overhead mist system until roots begin to develop. As with other trough systems, water or fertilizer solution flows down the length of the inside of the trough. While roots are developing (and plants are being misted), water is used in the trough to keep the substrate moist. After roots begin to develop, a fertilizer solution may be used to provide both water and mineral nutrients to the developing cutting (and mist may be terminated). When the cuttings are ready for shipping, the foam cubes or cutting trays are slid out of the trough and packaged for shipping.
When troughs are used, the same types of support components such as storage tanks, pumps, supply lines, recollection lines, filters, solution disinfesting systems and monitoring probes may be used as were discussed for ebb-and-flow benches. The primary difference in a trough system and an ebb-and-flow system is that in the ebb-and-flow system, the fertilizer solution is gradually and evenly raised up around the containers and then drained away. In a trough, plant roots are periodically or continuously exposed to a thin flowing stream or film of water or nutrients.
Gravel and weed-mat floors
Rather than growing on raised benches, plants may be grown directly on the greenhouse floor. In this case, the floor itself serves as the production surface. Advantages of growing on floors are that it affords the ability to maximize space usage efficiency and increases flexibility. In some cases, floor production systems may save money because no benches are required, but in other cases (i.e. flood floors) floor production systems may be initially more expensive than many types of raised benches.
One of the simplest floor systems is a gravel floor. In this case plants are grown on a pad of 3/8 inch crushed rock or pea gravel. This is a low-cost floor production system and the gravel allows for excellent drainage. However, weeds may grow in the gravel and sanitation can be difficult on gravel floors. It may also be difficult to have small containers sit upright and level on gravel floors. So, gravel floors work best with larger containers, containers in trays and flats.
Floors may also be covered with a polypropylene woven fabric (weed mat or ground cover). The fabric is typically black, at least 17 mils in thickness and may have lines or patterns to help with plant spacing. This is again a relatively low cost option that allows maximum use of space and provides flexibility. However, weed mat typically allows for slower drainage than gravel, collects substrate that washes from containers, can allow weeds to grown on top of or through openings in the mat and makes sanitation difficult. Floors with weed mat covering may also become uneven over time which can result in wet and dry spots in the crop. Wet areas can serve as locations where soil-borne diseases can begin to develop.
Concrete floors
Greenhouse floors may also be covered with concrete and the concrete floor used as the production surface. There are two basic types of concrete that may be used for greenhouse floors. The first is standard concrete. This material is made from Portland cement, aggregate, sand and water. It is strong and can support up to 2,500 lbs per square inch. However, standard concrete does not allow water to drain through. Porous concrete is made from Portland cement, aggregate and water. Being able to support up to 600 lbs per square inch, porous concrete is not as strong as standard concrete, but it allows water to drain through. Porous concrete should be avoided in locations such as potting or propagation areas. This is because substrate falling on the floors will tend to clog or block the pores of the concrete and hamper drainage. Also, the porous concrete is more difficult to clean than standard concrete.
Standard concrete is best used in areas where heavy weights must be supported (i.e. drives and walkways). Where standard concrete is used, it should be slightly sloped to allow water to drain off. Porous concrete is preferred in most situations where plants will be grown on greenhouse floors (excluding flood floor situations) because it is strong enough to support plants, people and light-weight equipment and because it drains. When using porous concrete for a greenhouse floor production surface, it should be poured over a gravel base so that the water is able to drain through the porous cement (rather than being blocked by an impervious layer).
In some situations, rubber tubing or pipes may be embedded in the concrete floors. This tubing is connected to a supply of hot water, and the hot water is circulated through the tubing in the floor and in this way the greenhouse is heated. In addition to being highly efficient, this type of heating system has the benefit of placing the heat source close the substrate (if the crop is being grown on the floor) and results in an increase in substrate temperature much like the Biotherm® heating system described in the heating unit.
Concrete floors prevent weeds and are generally easy to clean. They are durable and long-lasting and provide the advantage of maximizing space usage efficiency as well as flexibility.
Flood floors
Flood floors are in a sense hybrids of concrete floors and ebb-and-flow benches. The greenhouse floor is poured concrete with raised edges or curbs that allow the floor to be flooded and drained. As with ebb-and-flow benches, water or fertilizer solution moves into the substrate through capillary action.
There are two basic flood floor designs. The first is known as a traditional flood floor. In this type of flood floor, the concrete is poured and a laser is used to level the floor with a slight grade from the sides towards the center (creating a very shallow “V”). The center is usually 1 to 1 ½ inches lower than the high points along the curbs or edges. Water or fertilizer solution is pumped into the flood floor. In most cases, the inlets are located in the low center portion of the floor. The pump capacity is usually designed so that the flood floor can be filled to a depth of ¼ to ½ inch in approximately 5 minutes. The floor remains flooded for up to 10 minutes and is then drained back through the same supply line used to pump the solution into the flood floor. As with ebb-and-flow benches, the solution may be pumped through a filter before it is returned to the storage tank. The solution may also be treated with ultraviolet light, ozone, chloride, or copper to kill any potential plant pathogens.
Another basic type of flood floor is referred to as a cascading flood floor. This type of production surface combines the concept of food floors with troughs, and they are best suited for small containers (less than 6-inch containers). Cascading flood floors are concrete flood floors that are sloped from one side to the other with a drop of approximately ¼ to ⅜ inch from the high side to the low side. The water or fertilizer solution is pumped into the flood floor on the high side, flows down the slope and is recollected on the low side of the floor. The solution is pumped into the flood floor at a rate such that 30 to 45 seconds are required for the solution to cross the flood floor and a solution depth of approximately ¼ inch is maintained. The flooding process continues for approximately 10 minutes and is then terminated. The recollected water is pumped back to storage tanks. As with traditional flood floors and ebb-and-flood benches, the recollected solution is typically filters and may be treated for disease-causing pathogens. Regardless of the exact design, the advantages of flood floors include reduced water use, reduced fertilizer use, elimination of runoff, and high space usage efficiency. The primary disadvantage is the initial cost since they can be expensive to install.
Ground beds
Ground beds are most often used for cut flower or greenhouse vegetable production. They are filled with soil or artificial substrates in which plants are directly grown. Ground beds may have sidewalls and be elevated, or they may be level with the greenhouse floor. In some cases the ground beds might simply be the native field soil (sometimes amended and adjusted) that the greenhouse was built to cover.
Hanging basket systems
Hanging baskets may be placed on traditional benches or they may be grown using several types of elevated systems. Elevated systems offer the advantage of increasing spacing usage efficiency but hanging baskets may block light from reaching crops below them. The simplest system for hanging baskets is one in which baskets are hung using simple hooks. A drip irrigation tube is often placed in the hanging basket to provide water and mineral nutrition. Another system is referred to as an ECHO system. In this system, baskets are hung on hooks that are part of a rotating line. The line may be rotated when irrigation is required. As the containers pass one end of the loop, they pass under an irrigation nozzle. Finally, the cage system is one in which baskets are hung from a suspended cage or metal structure. This structure is usually automated so that it can be moved from one end of the greenhouse to the other. This allows material to be moved so that plant material under the baskets can receive sunlight for at least part of the day.
Section 4: Sanitation of Greenhouse Benches and Production Surfaces
Benches and production surfaces should be kept clean. Bacteria, fungi and algae may grow on benches and production surfaces (this can be particularly problematic on wooden benches and floor systems). A periodic disinfecting will help to control diseases as well as some common greenhouse pests. There are numerous materials on the market that can be used to clean and disinfect benches and production floor surfaces. Among these are the quaternary ammonium compounds such as GreenShield®, Physan® and Triathlon®. There are the hydrogen dioxide compounds Zerotol® and Oxidate® and the chlorine dioxide-based Selectrocide T®. In addition to these commercial products, chlorine bleach may be used to clean and disinfect production surfaces. All of these products are unique and greenhouse managers should carefully read the product labels and follow instructions when using these products.
Greenhouses should also be kept weed free. Weeds can harbor greenhouse pests and produce seed that find their way and germinate in flats or containers. Weeds should be continually removed even when the greenhouse is not in use. This will prevent weeds from being able to grow and seed out inside the greenhouse. Weeds outside of the greenhouse should also be kept mowed so that they do not seed and the seed find their way into the greenhouse.
Section 5: Calculating Production Surface Area and Space Usage Efficiency
In addition to designing the individual benches or production surfaces, the arrangement of the benches is important. Besides affecting traffic flow within the greenhouse, the benching arrangement affects the amount of space available under cover for production of crops (space usage efficiency). A greenhouse that has 10,000 ft2 under cover will not necessarily have 10,000 ft2 available for the production of crops. Some of the space will be used for walkways, work areas, and greenhouse systems. The space available for crop production should be maximized because this is the income generating area.
It is important to be able to calculate the square footage in a greenhouse, the square footage of production area under cover and the space usage efficiency. These calculations can be performed using a few simple geometric equations.
For rectangles (including squares), the length of the structure multiplied by the width of the structure provides the total number of square feet within the structure. As an example, we will determine the total square footage of space and the space usage efficiencies for two different bench arrangements in a greenhouse structure that is 38 ft wide and 60 ft long. In the first benching layout, the side benches (running the length of the greenhouse) are 2 ft wide and extend the entire length of the structure. There are 3 benches spaced across the greenhouse that are 6 ft wide. The central walkways between the benches are 4 ft wide and the end walkways are 5 ft wide.
The total area under cover is:
38 ft x 60 ft = 2280 ft2
The area in benching (production surface area) is:
2 x (2 ft x 60 ft) = 240 ft2
3 x (6 ft x 50 ft) = 900 ft2
240 ft2 + 900 ft2 = 1140 ft2
Therefore, the space usage efficiency for this benching layout is:
(1140 ft2 ÷ 2280 ft2) x 100 = 50%
If we put rolling benches into the same greenhouse structure, our production surface area and space usage efficiency changes. In this layout, there are two 2 ft wide benches along the length of the greenhouse. There is one 4 ft aisle. There are six 5 ft wide rolling benches. As before, there is a 5 ft walkway at the end of these benches on each end of the greenhouse.
The overall area under cover remains 2280 ft2
The two side benches still provide 240 ft2
The rolling benches provide 6 x (5 ft x 50 ft) = 1500 ft2
The total area in benching is 240 ft2 + 1500 ft2 = 1740 ft2
The usage efficiency is 100 x (1740 ft2 ÷ 2280 ft2) = 76%
By using rolling benches, the space usage efficiency increased from 50% to 76%, and we gain 600 ft2 of bench space that can generate revenue. We also created 600 ft2 of space over which we can spread certain production costs. In a purely hypothetical scenario, if the business is paying $5,000 per year on the cost of the structure, approximately $13.70 must be generated per day just to pay for the greenhouse. In the first benching scenario, there were 1140 ft2 of space that could generate revenue. Therefore, each ft2 of bench space must be charged approximately $0.012 per day just to pay for the greenhouse structure. A crop that occupies 1 ft2 of space (and thus each plant) for 6 weeks must be charged $0.50 to pay for that space. In the second scenario, each ft2 needs to be charged $0.008 per day. Therefore, the same crop would be charged $0.34 per plant. The business would save $0.16 in production costs per plant. These savings would go directly to the profit line of the business. All other fixed costs and some variable costs (i.e. heating) are accounted for in this way. Therefore, maximizing space usage efficiency reduces costs.
© M.R. Evans, 2008, 2009, 2011, 2014
Want more information on 358 security fence factory? Feel free to contact us.